Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C122D14  Brake Master Cylinder Pressure Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C122D14 Brake Master Cylinder Pressure Sensor Supply Voltage Circuit Short to Ground or Open Master cylinder pressure sensor power supply voltage decrease occurs or history of voltage decrease exists, and defective master cylinder pressure sensor output continues for 1.2 seconds or more.
·

Master cylinder pressure sensor output defective

·

Skid control ECU (Brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION



PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for 3 Door A
for 5 Door B



A

2.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

B

5.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
2.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A108-38 (+BS) - Body ground Always 11 to 14 V
A108-38 (+BS) - A108-25 (GND1) Always 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the A108 skid control ECU (brake actuator assembly) connector.


b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

c.

Press the DTC clear button.


d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C122D14 is not output A
C122D14 is output B



A

B

5.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-38 (+BS) - Body ground Always 11 to 14 V
A36-38 (+BS) - A36-25 (GND1) Always 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC
a.

Reconnect the A36 skid control ECU (brake actuator assembly) connector.


b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

c.

Press the DTC clear button.


d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C122D14 is not output A
C122D14 is output B



A

B