Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model TMC Made LHD) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0447308 BRAKE ACTUATOR(for Gasoline Model TMC Made LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model TMC Made LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Skid control ECU (brake actuator assembly) Update ECU security key Vehicle control history (RoB) are stored (Click here)
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 6.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 12601B 9.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 51410 10.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 55225C 11.REMOVE DASH PANEL HEAT INSULATOR

a.
C444955

Remove the nut.


b.
C444956

Remove the nut, clamp and dash panel heat insulator.


Hide 164A2 12.SEPARATE RESERVE SEALED TANK

a.
C444957

Remove the 2 bolts to separate the reserve sealed tank.


Hide 88707 13.REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
C444958

Remove the bolt.


b.
C444959

Rotate the hook connector and disconnect the air conditioning tube and accessory assembly as shown in the illustration.


c.

Remove the 2 O-rings from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



d.
C444960

Disengage the 2 clamps to separate the air conditioning tube and accessory assembly.


Hide 14.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C444961C01
0,0 0,0 false
V113147

Move in this Direction


Move aside the air conditioning tube and accessory assembly as shown in the illustration.

NOTICE:

Do not apply excessive force to the air conditioning tube and accessory assembly.



b.
C444962C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.
C444963C01
2.01,1.073 2.365,0.646 2.365,0.646 2.458,0.646 true 1.115,1.948 1.219,1.948 1.219,1.948 1.625,1.604 true 2.156,1.365 2.625,1.125 2.625,1.125 2.719,1.125 true 0.74,1.063 0.844,1.063 0.844,1.063 1.438,1.302 true 1.135,0.458 1.24,0.458 1.24,0.458 1.656,1.24 true 1.833,1.125 1.958,0.417 1.958,0.417 2.052,0.417 true 2.75,1.042 2.948,1.229 0.198,0.188 10 true *a 0.927,1.844 1.125,2.021 0.198,0.177 10 true *b 0.542,0.958 0.708,1.115 0.167,0.156 10 true *c 0.958,0.365 1.125,0.521 0.167,0.156 10 true *d 2.073,0.333 2.24,0.49 0.167,0.156 10 true *e 2.479,0.573 2.646,0.729 0.167,0.156 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


d.
C445359

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




e.
C444964

Disengage the 5 clamps to remove the No. 1 brake tube clamp from the brake lines.

NOTICE:

Do not kink or damage the brake lines.



f.
C444965

Disengage the 5 clamps to remove the No. 2 brake tube clamp from the brake lines.


g.
C444966

Disengage the clamp and remove the No. 2 brake tube clamp from the vehicle body.


h.
C444967

Remove the 2 nuts.


i.
C444968

Remove the bolt and brake actuator with bracket.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44591 15.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

a.
C444969

Remove the 3 nuts and No. 1 brake actuator bracket from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44510 16.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C444970

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44521A 17.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C444971

Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.


Hide 44547B 18.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C444972

Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.