Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  VSC OFF Switch Circuit  


DESCRIPTION

for 3 Door:

Operating the VSC OFF switch (combination switch assembly) makes it possible for TRC and/or VSC operation to be prohibited.

Pressing the VSC OFF switch (combination switch assembly) changes to TRC OFF mode, and turns off TRC operation. In addition, a TRC cancel message is displayed on the multi-information display in the combination meter assembly.

While the vehicle is stopped, pressing and holding the VSC OFF switch (combination switch assembly) for 3 seconds or more changes to VSC OFF mode, and turns off both TRC and VSC operation. In addition, a TRC cancel message is displayed on the multi-information display in the combination meter assembly, and the VSC OFF indicator light illuminates.

If the VSC OFF switch is pressed while SPORT or TRACK modes are selected, the mode changes to EXPERT mode, in which control is performed to help prevent the vehicle from spinning during oversteer maneuvers. In addition, the VSC OFF indicator light in the combination meter assembly illuminates, and "EXPERT" is displayed on the multi-information display.

for 5 Door:

Operating the VSC OFF switch (combination switch assembly) makes it possible for TRC and/or VSC operation to be prohibited.

Pressing the VSC OFF switch (combination switch assembly) changes to TRC OFF mode, and turns off TRC operation. In addition, a TRC cancel message is displayed on the multi-information display in the combination meter assembly.

While the vehicle is stopped, pressing and holding the VSC OFF switch (combination switch assembly) for 3 seconds or more changes to VSC OFF mode, and turns off both TRC and VSC operation. In addition, a TRC cancel message is displayed on the multi-information display in the combination meter assembly, and the VSC OFF indicator light illuminates.

WIRING DIAGRAM

for 3 Door
C449203E01
0.281,4.125 2.219,4.458 1.938,0.333 10 false Combination Meter Assembly 0.292,3.958 0.833,4.208 0.542,0.25 10 false H6 0.906,1.76 1.74,2.125 0.833,0.365 10 false CANH 0.917,0.948 1.75,1.313 0.833,0.365 10 false CANL 1.406,0.76 1.729,0.969 0.323,0.208 10 false 25 1.406,1.573 1.729,1.781 0.323,0.208 10 false 9 5.698,0.75 6.021,0.958 0.323,0.208 10 false 10 5.698,1.573 6.021,1.781 0.323,0.208 10 false 22 5.969,0.948 6.448,1.271 0.479,0.323 10 false CANL 5.969,1.76 6.448,2.083 0.479,0.323 10 false CANH 5.938,2.75 6.417,3.073 0.479,0.323 10 false CSW 5.688,2.75 6.01,2.958 0.323,0.208 10 false 33 3.667,2.76 3.99,2.969 0.323,0.208 10 false 5 3.833,2.781 4.219,2.99 0.385,0.208 10 false E 4.531,2.792 4.854,3 0.323,0.208 10 false + 2.917,4.365 4.896,4.635 1.979,0.271 10 false : CAN Communication Line 3.573,3.438 5.583,3.885 2.01,0.448 10 false VSC OFF Switch (Combination Switch Assembly) 5.521,4.01 7.083,4.729 1.563,0.719 10 false Skid Control ECU (Brake Actuator Assembly) 3.573,3.271 3.896,3.479 0.323,0.208 10 false H18 5.531,3.844 6.021,4.146 0.49,0.302 10 false A108 4.719,2.75 5.042,2.958 0.323,0.208 10 false 7

for 5 Door
C449203E02
0.281,4.125 2.219,4.458 1.938,0.333 10 false Combination Meter Assembly 0.292,3.958 0.833,4.208 0.542,0.25 10 false H6 0.906,1.76 1.74,2.125 0.833,0.365 10 false CANH 0.917,0.948 1.75,1.313 0.833,0.365 10 false CANL 1.406,0.76 1.729,0.969 0.323,0.208 10 false 25 1.406,1.573 1.729,1.781 0.323,0.208 10 false 9 5.698,0.75 6.021,0.958 0.323,0.208 10 false 10 5.698,1.573 6.021,1.781 0.323,0.208 10 false 22 5.969,0.948 6.448,1.271 0.479,0.323 10 false CANL 5.969,1.76 6.448,2.083 0.479,0.323 10 false CANH 5.938,2.75 6.417,3.073 0.479,0.323 10 false CSW 5.688,2.75 6.01,2.958 0.323,0.208 10 false 33 3.667,2.76 3.99,2.969 0.323,0.208 10 false 5 3.833,2.781 4.219,2.99 0.385,0.208 10 false E 4.531,2.792 4.854,3 0.323,0.208 10 false + 2.917,4.365 4.896,4.635 1.979,0.271 10 false : CAN Communication Line 3.573,3.438 5.583,3.885 2.01,0.448 10 false VSC OFF Switch (Combination Switch Assembly) 5.521,4.01 7.083,4.729 1.563,0.719 10 false Skid Control ECU (Brake Actuator Assembly) 3.573,3.271 3.896,3.479 0.323,0.208 10 false H18 5.531,3.844 5.854,4.052 0.323,0.208 10 false A36 4.719,2.75 5.042,2.958 0.323,0.208 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (TRC (TRAC)/VSC OFF MODE)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC expert mode(VSC expert mode MID ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
VSC expert mode(VSC expert mode MID ON): When TRC and VSC are prohibited during SPORT mode or TRACK mode
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45

b.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch (combination switch assembly) operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (TRC OFF Message) VSC OFF Indicator Light
Not pressed Normal mode (TRC(TRAC) ON/VSC ON) Not displayed Does not come on
Pressing the VSC OFF switch (combination switch assembly) TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) Displayed Does not come on
Pressing and holding the VSC OFF switch (combination switch assembly) VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

2.INSPECT COMBINATION SWITCH ASSEMBLY

B

C

2.INSPECT COMBINATION SWITCH ASSEMBLY
a.
C427247C01
1.167,1.75 1.583,1.333 true 2.417,1.75 2,1.333 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.021,1.698 1.177,1.896 0.156,0.198 10 false + 2.469,1.688 2.625,1.885 0.156,0.198 10 false E
*a Component without harness connected
(VSC OFF Switch (Combination Switch Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the H18 VSC OFF switch (combination switch assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-7 (+) - H18-5 (E) Switch pushed Below 1 Ω
H18-7 (+) - H18-5 (E) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE SPECIFICATION

NG

REPLACE COMBINATION SWITCH ASSEMBLY

3.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for 3 Door A
for 5 Door B



A

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-7 (+) - A108-33 (CSW) Always Below 1 Ω
H18-7 (+) or A108-33 (CSW) - Body ground Always 10 kΩ or higher
H18-5 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-7 (+) - A36-33 (CSW) Always Below 1 Ω
H18-7 (+) or A36-33 (CSW) - Body ground Always 10 kΩ or higher
H18-5 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR