This is the troubleshooting procedure for situations where the engine does not restart when attempting to restart it after a failed engine start occurred under stop and start system control.
This is the troubleshooting procedure for situations where the engine does not restart when attempting to restart it after either a failed engine start occurred under stop and start system control, or a mis-operation during vehicle takeoff resulted in an engine stall.
For information on stop and start control, refer to the system description.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>SYSTEM DESCRIPTION
PRECAUTIONS WHEN THE ENGINE STOP AND START ECU AND THE STARTER ASSEMBLY ARE REPLACED
When the engine stop and start ECU is replaced, it is necessary to read the number of starter operations before replacement and store this number in the new engine stop and start ECU after replacement, and to perform external backup boost converter (eco run vehicle converter assembly) existence learning. Moreover, initialization/learning of the air conditioning information and initialization/learning of the deceleration sensor zero point are also required.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the engine stop and start ECU or electromagnetic oil pump (oil pump assembly w/ solenoid) has been replaced, it is necessary to check the operation of the electromagnetic oil pump (oil pump assembly w/ solenoid).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the starter assembly is replaced, the number of starter operations stored in the engine stop and start ECU must be reset.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.
Inspect the fuses for circuits related to this system before performing the following procedure.
PRECAUTIONS FOR FOUR-WHEEL TOWING
Do not tow the vehicle with all 4 wheels on the ground.
Towing the vehicle with all 4 wheels on the ground may have a detrimental effect on the stop and start system, and could lead to damage.
If it is absolutely necessary to tow the vehicle with all 4 wheels on the ground, before towing first turn the ignition switch off. Then, turn the ignition switch to ON without starting the engine, and tow the vehicle.
PRECAUTIONS WHEN REPLACING ECM
When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check vehicle control history.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
| Vehicle control history [X0874: Stop & Start Restart Failure (Engine Restart after Engine Stall)] is output | A |
| Vehicle control history [X0874: Stop & Start Restart Failure (Engine Restart after Engine Stall)] is not output | B |
A
B
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check the vehicle specification
| Result | Proceed to |
|---|---|
| for CVT | A |
| for Manual Transaxle | B |
A
B
Consult with the customer to determine if they performed operations that could result in an AT engine stall.
(ex.) Heavy load, frequent shifts, etc.
| Result | Proceed to |
|---|---|
| Driver operations that could cause engine stall were performed | A |
| None of the above conditions are met | B |
A
B
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select the vehicle control history item [X0874: Stop&Start Restart Failure (Engine Restart after Engine Stall)] to display the data from the time of control.
Check the output data, and check whether operations were performed that could result in an MT engine stall.
| Result | Proceed to |
|---|---|
| When failure to restart from Stop and Start occurred, check whether the vehicle was put into "Shift Position" and "Clutch Lower Switch" was released (= incorrect operation). Or, for all recorded points, "Neutral Switch" is "OFF" (= driving range) | A |
| None of the above conditions are met | B |
A
B
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select the vehicle control history item [X0874: Stop&Start Restart Failure (Engine Restart after Engine Stall)] to display the data from the time of control.
Check the output data.
| Result | Proceed to |
|---|---|
All recorded sections "Starter" = OFF, and all recorded sections "Engine Speed" = 0 rpm
|
A |
"Starter" = ON for any sections, and all recorded sections "Engine Speed" = 0 rpm
|
B |
"Engine Speed" > 0 rpm for any sections
|
C |
A
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
It is possible that there is a malfunction of the starter drive circuit inside the stop and start ECU.
B
C
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check the vehicle control history item "Cranking Time".
| Result | Proceed to |
|---|---|
"Cranking Time" is 1.5 seconds or more
|
A |
"Cranking Time" is less than 1.5 seconds
|
B |
A
B
Disconnect the A67 engine stop and start ECU connector.
Turn the ignition switch to ON.
Turn off any electrical loads.
Measure the resistance according to the value(s) in the table below.
11 V or higher
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-1 (+B) - Body ground | Ignition switch ON | 11 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check the voltage of the auxiliary battery.
Depending on RoB detection timing, the minimum voltage from the previous startup will be stored for the Minimum Voltage (Cranking) and the Minimum Voltage (Starter Solenoid Engagement). For the battery condition at the start of the current driving cycle, see Battery Voltage.
When the value is 20, the value is being calculated.
| Result | Proceed to |
|---|---|
| Auxiliary battery voltage is 8.92 V or more | A |
| Auxiliary battery voltage is less than 8.92 V | B |
A
B
Measure the voltage of the auxiliary battery.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to display the "Cranking Time" and "Starter OFF Permission History (ECM)" data from the time of control.
Check the output data.
| Result | Proceed to | |
|---|---|---|
| "Cranking Time" is less than 1.5 seconds | "Starter OFF Permission History (ECM)" is ON
|
A |
"Starter OFF Permission History (ECM)" is OFF
|
B | |
| "Cranking Time" is 1.5 seconds or more. |
|
C |
A
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
Check whether the speed value of the EFI ECU is not a higher value than the original NE.
B
C
Enter the following menus: Powertrain / Stop and Start / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Using the Data List, check the current engine speed value of the stop and start ECU.
Stop and Start ECU "Engine Speed" > "Engine Speed (ENG)" + 300 rpm
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the RoB data points.
For each and all of the data points, "Engine Speed" > "Engine Speed (ECM)" + 300 rpm
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch(Hood Close)
| Tester Display |
|---|
| Starter Motor Drive Magnet Switch(Hood Close) |
Measure the voltage according to the value(s) in the table below.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
Using an oscilloscope, measure the waveform immediately after starting.
| Item | Content |
|---|---|
| Tester Connection | A67-21 (STA) - A67-6 (DGND) |
| Tool Setting | 10 V/DIV, 200 ms./DIV |
| Condition | During cranking |
Voltage and waveform both normal
| Proceed to |
|---|
| OK |
| NG |
OK
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
NG
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch(Hood Close)
| Tester Display |
|---|
| Starter Motor Drive Magnet Switch(Hood Close) |
Measure the voltage according to the value(s) in the table below.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
Using an oscilloscope, measure the waveform immediately after starting.
| Item | Content |
|---|---|
| Tester Connection | A67-21 (STA) - A67-6 (DGND) |
| Tool Setting | 10 V/DIV, 200 ms./DIV |
| Condition | During cranking |
Voltage and waveform both normal
| Proceed to |
|---|
| OK |
| NG |
OK
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Check the RoB data points.
When "Starter" is ON, there is even 1 point at which "Engine Speed" < 300 rpm
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check how long it took the engine to stall after turning the starter off.
| Result | Proceed to |
|---|---|
After starter turned off, engine immediately stalls.
|
A |
| After starter turned off, engine stalls after a time. | B |
A
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
B
for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>Engine Stalls
for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>Engine Stalls
for G16E-GTS: Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>Engine Stalls