Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2020.09–2021.04
RM36W0E _56 Audio / Visual / Telematics _091907 TELEMATICS _0434308 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telephone transceiver assembly, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15CB11 Telephone Main Antenna Circuit Short to Ground Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 8 antenna cord sub-assembly (for 3 Door)


B15CB13 Telephone Main Antenna Circuit Open Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 8 antenna cord sub-assembly (for 3 Door)



WIRING DIAGRAM

E434373E12
5.51,2.625 6.906,2.979 1.396,0.354 10 false Telephone Transceiver Assembly 5.313,0.99 5.927,1.188 0.615,0.198 10 false 1 5.292,1.573 5.906,1.771 0.615,0.198 10 false 1a 5.313,1.208 5.719,1.427 0.406,0.219 10 false E 3.813,0.99 4.427,1.188 0.615,0.198 10 false 1 3.781,1.583 4.396,1.781 0.615,0.198 10 false 1a 3.385,0.99 4,1.188 0.615,0.198 10 false 1 3.354,1.583 3.969,1.781 0.615,0.198 10 false 1a 3.365,1.208 3.604,1.396 0.24,0.188 10 false G 1.885,1.208 2.5,1.406 0.615,0.198 10 false H 2.156,2.156 3.427,2.5 1.271,0.344 10 false No. 2 Antenna Cord Sub-assembly 0.729,2.177 1.604,2.542 0.875,0.365 10 false Roof Antenna Assembly 4.094,2.146 5.271,2.583 1.177,0.438 10 false Antenna Cord Sub-assembly 5.313,1.792 5.719,2.01 0.406,0.219 10 false E 3.813,1.792 4.427,1.99 0.615,0.198 10 false F 3.823,1.208 4.438,1.406 0.615,0.198 10 false F 3.375,1.792 3.615,1.979 0.24,0.188 10 false G 1.885,1.792 2.5,1.99 0.615,0.198 10 false H 1.885,1.01 2.5,1.208 0.615,0.198 10 false 4 1.865,1.583 2.479,1.781 0.615,0.198 10 false 4a 0.198,0.104 1.708,0.469 1.51,0.365 12 false for 5 Door:

E452403E13
6.292,2.292 7.031,2.865 0.74,0.573 10 false Telephone Transceiver Assembly 5.958,0.75 6.573,0.948 0.615,0.198 10 false 1 5.938,1.583 6.552,1.781 0.615,0.198 10 false 1a 5.958,0.948 6.365,1.167 0.406,0.219 10 false E 4.688,0.75 5.302,0.948 0.615,0.198 10 false 1 4.667,1.583 5.281,1.781 0.615,0.198 10 false 1a 4.271,0.75 4.885,0.948 0.615,0.198 10 false 1 4.219,1.583 4.833,1.781 0.615,0.198 10 false 1a 4.24,0.948 4.479,1.135 0.24,0.188 10 false G 1.365,0.948 1.979,1.146 0.615,0.198 10 false H 3.125,2.208 4.365,2.542 1.24,0.333 10 false No. 2 Antenna Cord Sub-assembly 0.417,2.156 1.271,2.594 0.854,0.438 10 false Roof Antenna Assembly 4.948,2.219 5.844,2.604 0.896,0.385 10 false Antenna Cord Sub-assembly 5.958,1.781 6.365,2 0.406,0.219 10 false E 4.688,1.781 5.302,1.979 0.615,0.198 10 false F 4.688,0.948 5.302,1.146 0.615,0.198 10 false F 4.24,1.781 4.479,1.969 0.24,0.188 10 false G 1.375,1.802 1.99,2 0.615,0.198 10 false H 1.385,0.75 2,0.948 0.615,0.198 10 false 4 1.354,1.594 1.969,1.792 0.615,0.198 10 false 4a 0.125,0.104 1.917,0.667 1.792,0.563 12 false for 3 Door: 1.479,2.188 2.719,2.521 1.24,0.333 10 false No. 8 Antenna Cord Sub-assembly 3.052,1.792 3.667,1.99 0.615,0.198 10 false I 3.052,0.948 3.667,1.146 0.615,0.198 10 false I 2.594,1.792 3.208,1.99 0.615,0.198 10 false J 2.583,0.948 3.198,1.146 0.615,0.198 10 false J 2.563,1.604 3.177,1.802 0.615,0.198 10 false 1a 2.99,1.604 3.604,1.802 0.615,0.198 10 false 1a 3.042,0.75 3.385,0.948 0.344,0.198 10 false 1 2.583,0.75 2.927,0.948 0.344,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
DTC B15CB11 or B15CB13 is output B



A

B

3.INSPECT ROOF ANTENNA ASSEMBLY
3.INSPECT ROOF ANTENNA ASSEMBLY
a.
E271865C48
0.313,1 0.75,1.26 0.438,0.26 1.969,1.479 2.24,1.594 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.292,1.531 2.604,1.729 0.313,0.198 10 false 4a 0.49,1.063 0.646,1.26 0.156,0.198 10 false H
*a Component without harness connected
(Roof Antenna Assembly)


Remove the roof antenna assembly.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ROOF ANTENNA>REMOVAL



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-4 - H-4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

4.SYSTEM CHECK

NG

REPLACE ROOF ANTENNA ASSEMBLY

4.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
for 5 Door A
for 3 Door B



A

5.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

B

8.CHECK NO. 8 ANTENNA CORD SUB-ASSEMBLY
5.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E434374C01
1.51,0.042 1.927,0.26 0.417,0.219 1.521,2.063 1.938,2.281 0.417,0.219 1.052,1.417 1.552,1.042 true 0.479,3.146 0.813,2.885 true 0.854,1.354 1.167,1.552 0.313,0.198 10 false 4a 0.281,3.104 0.594,3.302 0.313,0.198 10 false 1a 1.677,2.104 1.833,2.302 0.156,0.198 10 false G 1.688,0.083 1.844,0.281 0.156,0.198 10 false H 0.208,0.125 0.521,0.323 0.313,0.198 10 false *a 0.219,2.063 0.531,2.26 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 2 antenna cord sub-assembly from the roof antenna assembly connector.


b.

Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-4 - G-1 Always Below 1 Ω
H-4a - G-1a Always Below 1 Ω
H-4 - G-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

6.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E434375C01
1.49,0.146 1.927,0.417 0.438,0.271 1.479,1.771 1.917,2.042 0.438,0.271 1.865,1.24 2.344,1.469 true 2.521,2.781 2.979,3.083 true 0.177,0.229 0.49,0.427 0.313,0.198 10 false *a 0.271,1.948 0.583,2.146 0.313,0.198 10 false *b 1.667,0.219 2.208,0.458 0.542,0.24 10 false E 1.677,1.844 2.219,2.083 0.542,0.24 10 false F 2.427,1.406 2.969,1.646 0.542,0.24 10 false 1a 3.073,3.031 3.427,3.302 0.354,0.271 10 false 1a
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)
*b Front view of wire harness connector
(to No. 2 antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna cord sub-assembly connector from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - F-1 Always Below 1 Ω
E-1a - F-1a Always Below 1 Ω
E-1 or F-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT

8.CHECK NO. 8 ANTENNA CORD SUB-ASSEMBLY
a.
E452663C05
1.51,0.042 1.927,0.26 0.417,0.219 1.521,2.063 1.938,2.281 0.417,0.219 1.063,1.188 1.583,1.021 true 3.042,3.094 2.594,2.938 true 0.896,1.104 1.208,1.302 0.313,0.198 10 false 4a 3.094,3.021 3.406,3.219 0.313,0.198 10 false 1a 1.677,2.104 1.833,2.302 0.156,0.198 10 false J 1.688,0.083 1.844,0.281 0.156,0.198 10 false H 0.208,0.125 0.521,0.323 0.313,0.198 10 false *a 0.219,2.063 0.531,2.26 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the No. 8 antenna cord sub-assembly from the roof antenna assembly connector.


b.

Disconnect the No. 8 antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-4 - J-1 Always Below 1 Ω
H-4a - J-1a Always Below 1 Ω
H-4 or J-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 8 ANTENNA CORD SUB-ASSEMBLY

9.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E452664C04
1.479,0.271 1.896,0.49 0.417,0.219 1.521,2.063 1.938,2.281 0.417,0.219 0.698,1.573 0.885,1.208 true 0.427,3.177 0.813,2.875 true 0.604,1.563 0.917,1.76 0.313,0.198 10 false 1a 0.24,3.083 0.552,3.281 0.313,0.198 10 false 1a 1.677,2.104 1.833,2.302 0.156,0.198 10 false G 1.656,0.302 1.813,0.5 0.156,0.198 10 false I 0.208,0.125 0.521,0.323 0.313,0.198 10 false *a 0.219,2.063 0.531,2.26 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 8 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 2 antenna cord sub-assembly from the No. 8 antenna cord sub-assembly connector.


b.

Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-1 - G-1 Always Below 1 Ω
I-1a - G-1a Always Below 1 Ω
I-1 or G-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

10.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E434375C01
1.49,0.146 1.927,0.417 0.438,0.271 1.479,1.771 1.917,2.042 0.438,0.271 1.865,1.24 2.344,1.469 true 2.521,2.781 2.979,3.083 true 0.177,0.229 0.49,0.427 0.313,0.198 10 false *a 0.271,1.948 0.583,2.146 0.313,0.198 10 false *b 1.667,0.219 2.208,0.458 0.542,0.24 10 false E 1.677,1.844 2.219,2.083 0.542,0.24 10 false F 2.427,1.406 2.969,1.646 0.542,0.24 10 false 1a 3.073,3.031 3.427,3.302 0.354,0.271 10 false 1a
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)
*b Front view of wire harness connector
(to No. 2 antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna cord sub-assembly connector from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - F-1 Always Below 1 Ω
E-1a - F-1a Always Below 1 Ω
E-1 or F-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT