Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for 5 Door) › 2020.09–2021.11
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0452517 FRONT SEAT OUTER BELT ASSEMBLY(for 5 Door) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for 5 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73210 1.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.
B583423N01
1.979,0.24 2.208,0.438 0.229,0.198 10 true (A) 2.073,1.906 2.313,2.104 0.24,0.198 10 true (B)

Engage the guides to temporarily install the front seat outer belt assembly.


b.

Temporarily install the 2 bolts.


c.

Tighten bolt (A) and then bolt (B).

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.


B583522C01
2.094,2.479 2.344,2.313 true 5.438,2.5 5.688,2.333 true 0.052,0.052 0.427,0.323 0.375,0.271 12 false *A 3.74,0.052 4.031,0.292 0.292,0.24 12 false *B 1.896,2.375 2.146,2.625 0.25,0.25 10 false *a 5.25,2.396 5.5,2.646 0.25,0.25 10 false *a
*A for TMMF Made *B for TMC Made
*a Locking Button - -



e.

Connect the shoulder anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Check that the ELR locks.

NOTICE:

This check should be performed with the front seat outer belt assembly installed to the vehicle.


i.

With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.



h.

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62411B 2.INSTALL CENTER PILLAR UPPER GARNISH

Hide 62413A 3.INSTALL CENTER PILLAR LOWER GARNISH

Hide 73210 4.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73233 5.INSTALL LAP BELT OUTER ANCHOR COVER

a.
B583426C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claws to install the lap belt outer anchor cover.


Hide 62312B 6.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Connect the front door opening trim weatherstrip.


Hide 62331A 8.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Connect the rear door opening trim weatherstrip.


Hide 67917F 9.INSTALL REAR DOOR SCUFF PLATE INSIDE

Hide 76974F 10.INSTALL REAR UNDER SIDE COVER (for HV Model)

Hide 72693 11.INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Hide 12.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Hide 73350C 13.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 15.INSTALL INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART