Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door) › from 2020.09
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0452520 FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



Hide 3.DISCONNECT REAR SEATBACK ASSEMBLY

Hide 4.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 5.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 73233 7.REMOVE LAP BELT OUTER ANCHOR COVER

a.
B601702

Disengage the claws and guide to remove the lap belt outer anchor cover.


Hide 73220 8.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B601703

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62520B 9.REMOVE QUARTER TRIM PANEL ASSEMBLY

Hide 62412B 10.REMOVE CENTER PILLAR UPPER GARNISH

Hide 73220 11.REMOVE FRONT SEAT OUTER BELT ASSEMBLY

a.
B601704

Remove the bolt to disconnect the shoulder anchor of the front seat outer belt assembly.


b.
B601705C01
0.458,0.75 0.552,1.083 false 1.281,0.417 1.052,0.75 true 0.354,0.542 0.667,0.698 0.313,0.156 10 false *a 1.271,0.25 1.583,0.406 0.313,0.156 10 false *1
*a Protective Tape
*1 Locking Button


Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.


c.
B601706

Remove the 2 bolts.


d.

Disengage the guides to remove the front seat outer belt assembly.