55302C
1.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for Integrated Type)
55302C
2.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for Separate Type)
55085
3.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)
55085
4.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)
5.REMOVE FRONT SEAT ASSEMBLY LH
6.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
7.REMOVE REAR SEAT ASSEMBLY
64330D
8.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
Disengage the hooks to remove the package tray trim panel assembly.
58410B
9.REMOVE DECK BOARD ASSEMBLY
Remove the deck board assembly.
64995
10.REMOVE DECK FLOOR BOX RH
Remove the deck floor box RH.
64997
11.REMOVE DECK FLOOR BOX LH
Remove the deck floor box LH.
67914B
12.REMOVE FRONT DOOR SCUFF PLATE LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claws and guides to remove the front door scuff plate LH as shown in the illustration.
67913B
13.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62112
14.REMOVE COWL SIDE TRIM BOARD LH
|
Remove in this Direction |
Remove the clip.
Disengage the clip to remove the cowl side trim board LH as shown in the illustration.
62111C
15.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
63376B
16.DISCONNECT NO. 1 ROOF HEADLINING MOULDING LH
63375B
17.DISCONNECT NO. 1 ROOF HEADLINING MOULDING RH
Use the same procedure as for the LH side.
62312B
18.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
19.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62212
20.REMOVE FRONT PILLAR GARNISH LH
62211
21.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
73233
22.REMOVE LAP BELT OUTER ANCHOR COVER
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door)>REMOVAL
Use the same procedure as for the opposite side.
73220
23.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
73210
24.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
71304C
25.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
Remove the bolt and rear seatback hinge sub-assembly LH.
71303C
26.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure as for the RH side.
62520B
27.REMOVE QUARTER TRIM PANEL ASSEMBLY LH
|
Remove in this Direction |
Disengage the claws, clips and guide to remove the quarter trim panel assembly LH as shown in the illustration.
62510M
28.REMOVE QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
62412B
29.REMOVE CENTER PILLAR UPPER GARNISH LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the 2 clips.
Disengage the clip and guides to remove the center pillar upper garnish LH as shown in the illustration.
62411B
30.REMOVE CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
64716D
31.REMOVE DECK TRIM REAR COVER
Disengage the clips to remove the deck trim rear cover.
64740C
32.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Remove the 3 clips and deck trim side panel assembly LH.
64730B
33.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
73370E
34.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
73360D
35.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62472A
36.REMOVE INNER ROOF SIDE GARNISH LH
|
Remove in this Direction |
Disengage the clips to remove the inner roof side garnish LH as shown in the illustration.
62471A
37.REMOVE INNER ROOF SIDE GARNISH RH
Use the same procedure as for the LH side.
62452
38.REMOVE ROOF SIDE INNER GARNISH LH
|
Remove in this Direction |
Disengage the clips to remove the roof side inner garnish LH as shown in the illustration.
62451
39.REMOVE ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
74320
40.REMOVE VISOR ASSEMBLY LH
74310
41.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348C
42.REMOVE VISOR HOLDER
Use the same procedures for the opposite side.
|
Turn in this Direction |
|
Remove in this Direction |
Turn the visor holder counterclockwise approximately 45° and pull it out as shown in the illustration.
|
Remove in this Direction |
Disengage the claws to remove the base as shown in the illustration.
74612
43.REMOVE ASSIST GRIP COVER
Use the same procedure for all assist grip sub-assemblies.
| *a | Cutout |
Insert SST into the cutout of the assist grip cover as shown in the illustration.
To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.
| *a | 30 to 45° |
|
Remove in this Direction |
Pull SST as shown in the illustration to disengage the claw.
To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.
Remove the assist grip cover.
Use the same procedures for the opposite side.
74610A
44.REMOVE ASSIST GRIP SUB-ASSEMBLY
Use the same procedures for the opposite side.
|
Remove in this Direction |
Disengage the clips to remove the assist grip sub-assembly as shown in the illustration.
Remove the 2 clips from the vehicle body.
81260A
45.REMOVE MAP LIGHT ASSEMBLY
81240J
46.REMOVE ROOM LIGHT ASSEMBLY
89732A
47.REMOVE THEFT WARNING ULTRASONIC SENSOR (w/ Intrusion Sensor)
89943
48.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
87818
49.REMOVE INNER REAR VIEW MIRROR COVER (w/o Toyota Safety Sense 2)
86466E
50.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
86466D
51.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
63311C
52.REMOVE ROOF HEADLINING
for Front Pillar LH Side:
Disconnect the 2 connectors.
Using a clip remover, disengage the clamps.
for Front Pillar RH Side:
Disconnect the connector.
Using a clip remover, disengage the clamps.
for Windshield Glass Side:
w/o Toyota Safety Sense 2:
Disconnect the 2 connectors.
w/ Toyota Safety Sense 2:
Disconnect the 4 connectors.
for Rear Pillar RH Side:
Disconnect the connector.
Remove the bolt.
Using a clip remover, disengage the clamps.
Using a clip remover, remove the 3 clips.
Disconnect the connector.
|
Remove in this Direction |
Turn the roof headlining diagonally and bend slightly to remove it from the passenger door.
Make sure that wrinkles do not form in the roof headlining during removal.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.