Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door) › from 2020.09
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0452520 FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73220 1.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.

Inspect the front seat outer belt assembly.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door)>INSPECTION


b.
B601706N01
2.083,0.313 2.354,0.5 0.271,0.188 10 true (A) 2.115,1.906 2.385,2.094 0.271,0.188 10 true (B)

Engage the guides to temporarily install the front seat outer belt assembly.


c.

Temporarily install the 2 bolts.


d.

Tighten bolt (A) and then bolt (B).

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


e.
B601704

Connect the shoulder anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.
B601703

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.
B597063

Check that the ELR locks.

NOTICE:

This check should be performed with the front seat outer belt assembly installed to the vehicle.


i.

With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.



h.

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


i.
B601707C01
2.25,0.438 2.469,0.698 false 2.156,0.26 2.469,0.417 0.313,0.156 10 false *1
*1 Locking Button


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



Hide 62412B 2.INSTALL CENTER PILLAR UPPER GARNISH

Hide 62520B 3.INSTALL QUARTER TRIM PANEL ASSEMBLY

Hide 73220 4.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B601703

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73233 5.INSTALL LAP BELT OUTER ANCHOR COVER

a.
B601702

Engage the guide and claws to install the lap belt outer anchor cover.


Hide 72693 7.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 8.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 9.INSTALL REAR SEATBACK ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 11.INSTALL INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART