Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00701A  Driver Seat Belt Pretensioner "A" Deployment Control Circuit Resistance Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B00701A Driver Seat Belt Pretensioner "A" Deployment Control Circuit Resistance Below Threshold
·

The airbag sensor assembly detects a line short in the driver seat pretensioner squib circuit for 2 seconds during the primary check

·

Front seat outer belt assembly RH malfunction*1

·

Front seat outer belt assembly LH malfunction*2

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Front seat outer belt assembly RH*1

·

Front seat outer belt assembly LH*2

·

Airbag sensor assembly


Comes on Applies to check mode

*1: for RHD

*2: for LHD


WIRING DIAGRAM

for RHD:
B502460E84
4.896,3.083 7.094,3.542 2.198,0.458 10 false Airbag Sensor Assembly 4.885,2.917 6.125,3.104 1.24,0.188 10 false O24 4.781,1.333 5.583,1.979 0.802,0.646 10 false 4 4.771,1.896 5.573,2.542 0.802,0.646 10 false 3 4.958,1.333 5.76,1.979 0.802,0.646 10 false PR+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false PR- 0.875,2.406 1.76,2.583 0.885,0.177 10 false O14 0.875,2.573 3.417,3.385 2.542,0.813 10 false Front Seat Outer Belt Assembly RH 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.802,1.333 2.604,1.979 0.802,0.646 10 false R+ 1.833,1.885 2.635,2.531 0.802,0.646 10 false R-

for LHD:
B502460E83
4.896,3.083 7.01,3.563 2.115,0.479 10 false Airbag Sensor Assembly 4.885,2.917 6.156,3.104 1.271,0.188 10 false O24 4.781,1.333 5.583,1.979 0.802,0.646 10 false 5 4.781,1.896 5.583,2.542 0.802,0.646 10 false 6 4.958,1.333 5.76,1.979 0.802,0.646 10 false PL+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false PL- 0.875,2.406 2.438,2.604 1.563,0.198 10 false O13 0.875,2.573 3.406,3.531 2.531,0.958 10 false Front Seat Outer Belt Assembly LH 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.813,1.333 2.615,1.979 0.802,0.646 10 false L+ 1.844,1.885 2.646,2.531 0.802,0.646 10 false L-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
Current B00701A is output A
History B00701A is output B



Post-procedure1

c.

None



A

2.CHECK VEHICLE TYPE

B

USE SIMULATION METHOD TO CHECK

2.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for RHD A
for LHD B



A

3.CHECK CONNECTION OF CONNECTORS

B

10.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the front seat outer belt assembly RH and airbag sensor assembly.


Procedure1

b.
C422858C02
0.521,1.021 0.521,1.635 false 1.365,0.521 1.365,0.885 false 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.281,0.323 1.583,0.51 0.302,0.188 10 false *3
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



d.

Check that the wire harness connector (on the front seat outer belt assembly RH side) is not loose, deformed or damaged.

OK:

The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

5.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
a.
C422851C06
0.396,2.25 0.781,2.521 0.385,0.271 0.667,0.667 0.667,1.063 false 1.802,2.313 1.979,2.313 false 1.49,0.656 1.49,1.052 false 0.594,1.073 0.99,1.417 0.396,0.344 10 false *1 2.26,0.823 2.573,1.156 0.313,0.333 10 false *2 1.802,0.51 2.01,0.76 0.208,0.25 10 false A 1.646,0.51 1.813,0.865 0.167,0.354 10 false B 1.146,0.5 1.698,0.969 0.552,0.469 10 false C 0.781,0.51 1.365,1.052 0.583,0.542 10 false D 0.448,2.281 0.771,2.5 0.323,0.219 10 false O14 2.01,2.219 2.448,2.563 0.438,0.344 10 false SST 0.344,1.719 0.646,2 0.302,0.281 10 false *a 1.417,1.073 1.698,1.292 0.281,0.219 10 false *3
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the connector to the airbag sensor assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
6.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B00701A may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B00701A is not output A
B00701A is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

B

7.CHECK WIRE HARNESS (SHORT)
7.CHECK WIRE HARNESS (SHORT)

Pre-procedure1

a.

Disconnect the connector from the airbag sensor assembly.


b.

Release the activation prevention mechanism built into connector B.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION



Procedure1

c.
C422852C06
0.604,2.375 0.979,2.625 0.375,0.25 1.531,2.333 1.844,2 true 1.031,2 1.333,2.333 true 0.583,1 0.583,0.667 false 1.417,1 1.417,0.667 false 0.5,1.021 0.75,1.333 0.25,0.313 10 false *1 2.396,0.833 2.771,1.271 0.375,0.438 10 false *2 1.938,0.51 2.24,0.865 0.302,0.354 10 false A 1.563,0.51 1.906,1.052 0.344,0.542 10 false B 1.052,0.51 1.49,0.906 0.438,0.396 10 false C 0.677,0.51 1.115,0.896 0.438,0.385 10 false D 1.885,1.917 2.188,2.208 0.302,0.292 10 false R- 0.813,1.917 1.094,2.135 0.281,0.219 10 false R+ 0.354,1.844 0.75,2.135 0.396,0.292 10 false *a 0.646,2.385 0.99,2.604 0.344,0.219 10 false O14 1.365,1.021 1.667,1.333 0.302,0.313 10 false *3
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O14-1 (R+) - O14-2 (R-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Restore the released activation prevention mechanism of connector B to the original condition.



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC
a.
C422848C02
0.813,0.833 0.813,1.156 false 0.927,0.688 1.083,1 0.156,0.313 10 false D 1.083,0.688 1.229,0.948 0.146,0.26 10 false C 1.583,0.688 1.74,0.948 0.156,0.26 10 false B 1.74,0.688 1.979,1 0.24,0.313 10 false A 2.188,1 2.625,1.344 0.438,0.344 10 false *2 0.74,1.177 0.99,1.417 0.25,0.24 10 false *1
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC
9.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B00701A may be output at this time, but they are not related to this check.


Result:
Result Proceed to
B00701A is not output A
B00701A is output B



Post-procedure1

c.

None



A

USE SIMULATION METHOD TO CHECK

B

10.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

11.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

11.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the front seat outer belt assembly LH and airbag sensor assembly.


Procedure1

b.
C422858C02
0.521,1.021 0.521,1.635 false 1.365,0.521 1.365,0.885 false 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.281,0.323 1.583,0.51 0.302,0.188 10 false *3
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness


Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



d.

Check that the wire harness connector (on the front seat outer belt assembly LH side) is not loose, deformed or damaged.

OK:

The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

12.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
a.
C422851C05
0.396,2.25 0.76,2.5 0.365,0.25 0.667,0.667 0.667,1.063 false 1.802,2.313 1.979,2.313 false 1.49,0.656 1.49,1.052 false 0.594,1.073 0.99,1.417 0.396,0.344 10 false *1 2.26,0.823 2.573,1.156 0.313,0.333 10 false *2 1.813,0.51 2,0.74 0.188,0.229 10 false A 1.656,0.51 1.813,0.74 0.156,0.229 10 false B 1.146,0.51 1.281,0.76 0.135,0.25 10 false C 0.781,0.51 0.958,0.781 0.177,0.271 10 false D 0.438,2.271 0.781,2.49 0.344,0.219 10 false O13 2.01,2.219 2.448,2.563 0.438,0.344 10 false SST 0.344,1.719 0.646,2 0.302,0.281 10 false *a 1.417,1.073 1.698,1.292 0.281,0.219 10 false *3
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

13.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
13.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B00701A may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B00701A is not output A
B00701A is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

B

14.CHECK WIRE HARNESS (SHORT)
14.CHECK WIRE HARNESS (SHORT)

Pre-procedure1

a.

Disconnect the connector from the airbag sensor assembly.


b.

Release the activation prevention mechanism built into connector B.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION



Procedure1

c.
C422852C05
0.604,2.375 0.979,2.615 0.375,0.24 1.531,2.333 1.844,2 true 1.031,2 1.333,2.333 true 0.583,1 0.583,0.667 false 1.417,1 1.417,0.667 false 0.5,1.021 0.75,1.333 0.25,0.313 10 false *1 2.406,0.844 2.781,1.281 0.375,0.438 10 false *2 1.938,0.5 2.24,0.854 0.302,0.354 10 false A 1.573,0.5 1.917,1.042 0.344,0.542 10 false B 1.063,0.5 1.5,0.896 0.438,0.396 10 false C 0.688,0.5 1.125,0.885 0.438,0.385 10 false D 1.885,1.917 2.188,2.208 0.302,0.292 10 false L- 0.813,1.917 1.094,2.135 0.281,0.219 10 false L+ 0.354,1.844 0.75,2.135 0.396,0.292 10 false *a 0.646,2.385 1.01,2.698 0.365,0.313 10 false O13 1.365,1.021 1.667,1.333 0.302,0.313 10 false *3
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O13-1 (L+) - O13-2 (L-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Restore the released activation prevention mechanism of connector B to the original condition.



OK

15.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CLEAR DTC
a.
C422848C02
0.813,0.833 0.813,1.156 false 0.927,0.688 1.083,1 0.156,0.313 10 false D 1.083,0.688 1.229,0.948 0.146,0.26 10 false C 1.583,0.688 1.74,0.948 0.156,0.26 10 false B 1.74,0.688 1.979,1 0.24,0.313 10 false A 2.188,1 2.625,1.344 0.438,0.344 10 false *2 0.74,1.177 0.99,1.417 0.25,0.24 10 false *1
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC
16.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B00701A may be output at this time, but they are not related to this check.


Result:
Result Proceed to
B00701A is not output A
B00701A is output B



Post-procedure1

c.

None



A

USE SIMULATION METHOD TO CHECK

B