Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2020.09
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E445957E02
1.292,0.479 3.74,0.677 2.448,0.198 10 false to Other Systems 5.052,1.865 5.365,2.063 0.313,0.198 10 false 11 1.927,1.865 2.24,2.063 0.313,0.198 10 false 36 5.344,1.948 6.073,2.146 0.729,0.198 10 false SPD 1.615,1.958 2.344,2.156 0.729,0.198 10 false +S 5,2.75 6.156,2.979 1.156,0.229 10 false H137*1, O122*2 0.552,2.698 1.281,2.896 0.729,0.198 10 false H6 5,2.938 6.729,3.365 1.729,0.427 10 false Stereo Component Amplifier Assembly 0.542,2.844 2.552,3.198 2.01,0.354 10 false Combination Meter Assembly 0.438,3.396 2.354,3.667 1.917,0.271 10 false *1: except G16E-GTS 2.146,3.406 4.063,3.677 1.917,0.271 10 false *2: for G16E-GTS

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E396774C37
1.448,0.188 1.948,0.5 0.5,0.313 0.698,2.052 1.083,1.521 true 0.573,2.063 0.885,2.26 0.313,0.198 10 false S+ 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.604,0.271 1.917,0.469 0.313,0.198 10 false H6 2.802,3.604 3.26,3.802 0.458,0.198 10 false GND 1.125,3.875 1.344,4.094 0.219,0.219 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal H6-36 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H6-36 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK MODEL

NG

2.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
except G16E-GTS A
for G16E-GTS B



A

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

B

4.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265796C69
1.583,0.417 2,0.667 0.417,0.25 0.875,0.917 1.354,1.25 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 1.635,0.448 2.094,0.635 0.458,0.188 10 false H137 0.531,0.833 1,1.073 0.469,0.24 10 false SPD 4.573,1.813 4.885,2.01 0.313,0.198 10 false A 5.969,1.563 6.469,1.854 0.5,0.292 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)
- -


i.

Remove the stereo component amplifier assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


ii.

Connect an oscilloscope to terminal H137-11 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H137-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265796C74
1.583,0.417 2,0.667 0.417,0.25 0.875,0.917 1.354,1.25 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 1.635,0.458 2.094,0.646 0.458,0.188 10 false O122 0.531,0.833 1,1.073 0.469,0.24 10 false SPD 4.573,1.813 4.885,2.01 0.313,0.198 10 false A 5.969,1.563 6.469,1.854 0.5,0.292 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)
- -


i.

Remove the stereo component amplifier assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


ii.

Connect an oscilloscope to terminal O122-11 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal O122-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR