Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › from 2020.09
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421656 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



B332383C05
0.719,0.146 1.031,0.344 0.313,0.198 10 false *a 2.479,0.146 2.792,0.344 0.313,0.198 10 false *b
*a Centering Bolt
*b Standard Bolt


PROCEDURE

Hide 67005 1.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas "A" to "K" are within the standard ranges.

B565054N01
0.615,0.188 0.771,0.385 0.156,0.198 10 false A 1.031,0.625 1.188,0.823 0.156,0.198 10 false B 2.042,0.208 2.198,0.406 0.156,0.198 10 false C 2.5,0.625 2.656,0.823 0.156,0.198 10 false D 3.844,0.708 4,0.906 0.156,0.198 10 false E 4.844,0.198 5,0.396 0.156,0.198 10 false F 6.594,1.938 6.75,2.135 0.156,0.198 10 false G 6.458,2.354 6.615,2.552 0.156,0.198 10 false H 5.396,4.063 5.542,4.26 0.146,0.198 10 false I 4.125,4.073 4.281,4.271 0.156,0.198 10 false J 2.573,4.031 2.729,4.229 0.156,0.198 10 false K

Standard Clearance:
Area Measurement Area Measurement
A 6.0 to 9.0 mm (0.236 to 0.354 in.) B -0.5 to 2.5 mm (-0.0197 to 0.098 in.)
C 6.0 to 9.0 mm (0.236 to 0.354 in.) D -0.5 to 2.5 mm (-0.0197 to 0.098 in.)
E 3.0 to 8.0 mm (0.118 to 0.315 in.) F 4.8 to 7.8 mm (0.189 to 0.307 in.)
G 4.9 to 8.9 mm (0.193 to 0.350 in.) H 3.1 to 8.1 mm (0.122 to 0.319 in.)
I 3.5 to 8.5 mm (0.138 to 0.335 in.) J 3.5 to 8.5 mm (0.138 to 0.335 in.)
K 4.2 to 9.2 mm (0.165 to 0.362 in.) - -



Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 64771G 3.REMOVE SPARE WHEEL COVER (for 5 Door)

Hide 67005 5.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

a.
B565055

Loosen the 4 hinge bolts on the back door and adjust the back door position.


b.

Tighten the 4 hinge bolts on the back door after adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Use the same procedure for the RH side and LH side.



c.
B565056

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


d.

Using a brass bar and a hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 64771G 7.INSTALL SPARE WHEEL COVER (for 5 Door)