This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B228562 | Steering Lock Position Signal Compare Failure | The steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match. (1-trip detection logic*1) | ·
LIN communication system ·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector ·
Telematics transceiver*2 |
DTC Output Confirmation Operation:
Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait at least 40 seconds with the ignition switch off (wait is the steering locked), then turn the ignition switch to ON (steering unlocked) and wait at least 40 seconds. |
*1: Only detected while a malfunction is present and the ignition switch is ON.
*2: w/ Remote Engine Starter System
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The engine cannot be started. | The ECU does not send an engine start request. |
| DTC No. | Data List and Active Test |
|---|---|
| B228562 | Power Source Control
Steering Unlock Switch Entry&Start
·
Power Supply Short History ·
Motor Driver Short History ·
Lock Bar Stuck Error History |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or telematics transceiver*1, refer to Service Bulletin.
*1: w/ Remote Engine Starter System
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Check for DTCs.
If the steering cannot be unlocked, the ignition switch cannot be turned to ON and the engine cannot be started.
If LIN communication is not available, the steering cannot be locked or unlocked.
LIN communication system DTC B278588 is not output simultaneously.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-4 (SLP1) - Body ground | Steering locked | 11 to 14 V |
| H71-4 (SLP1) - Body ground | Steering unlocked | Below 1.5 V |
Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) | OFF or ON | OFF: Steering locked | for CVT:
·
When the shift lever is in P and the ignition switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned ACC or ON, the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. for Manual Transaxle:
·
When the ignition switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned ACC or ON, the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. |
| Tester Display |
|---|
| Steering Unlock Switch |
The GTS display changes.
| Result | Proceed to |
|---|---|
| The value of Steering Unlock Switch is OFF | A |
| The value of Steering Unlock Switch is not OFF | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) | OFF or ON | ON: Steering unlocked | for CVT:
·
When the shift lever is in P and the ignition switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned ACC or ON, the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. for Manual Transaxle:
·
When the ignition switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned ACC or ON, the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. |
| Tester Display |
|---|
| Steering Unlock Switch |
The GTS display changes.
| Result | Proceed to |
|---|---|
| The value of Steering Unlock Switch is ON | A |
| The value of Steering Unlock Switch is not ON | B |
A
B
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-4 (SLP1) - Body ground | Steering locked | 10 kΩ or higher |
| H71-4 (SLP1) - Body ground | Steering unlocked* | Below 1 Ω |
*: If any of the doors are opened with the shift lever in P (fo CVT) and the ignition switch off, the steering will be locked. If the ignition switch is turned to ACC or ON with the electrical key transmitter sub-assembly in the cabin, the steering will be unlocked.
DTC B228562 may be stored due to a malfunction in the steering lock ECU (steering lock actuator or upper bracket assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator or upper bracket assembly) to the certification ECU (smart key ECU assembly) individually.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Remote Engine Starter System | A |
| w/o Remote Engine Starter System | B |
A
B
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the H85 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H46-11 (SLP) - H71-4 (SLP1) | Always | Below 1 Ω |
| H71-4 (SLP1) - H85-30 (SLPD) | Always | Below 1 Ω |
| H46-11 (SLP) or H71-4 (SLP1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the push-button start function.
Enter the vehicle while carrying an electrical key transmitter sub-assembly.
Depress the brake pedal with the shift lever in P.
Check that the engine starts when the engine switch is pressed.
| Result | Proceed to |
|---|---|
| Engine starts | A |
| Engine does not start | B |
A
B
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H46-11 (SLP) - H71-4 (SLP1) | Always | Below 1 Ω |
| H46-11 (SLP) or H71-4 (SLP1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG