Refer to Step 50 for the front door scuff plate (w/ Plate) installation procedure.
63311C
1.INSTALL ROOF HEADLINING (for Normal Roof)
|
Install in this Direction |
Insert the roof headlining into the cabin from the back door as shown in the illustration.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
for TMC Made:
Engage the guides to set the roof headlining.
Install the 2 clips.
for TMMF Made:
Engage the guides to set the roof headlining.
Install the 4 clips.
for Roof Rear Side:
Engage the guide.
Install the ground wire with the bolt.
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Windshield Glass Side:
for TMC Made:
Connect the 2 connectors.
for TMMF Made with EC Mirror:
Connect the 2 connectors.
for TMMF Made with Toyota Safety Sense 2:
Connect the 3 connectors.
for TMMF Made with Toyota Safety Sense 2 and EC Mirror:
Connect the 4 connectors.
for Front Pillar RH Side:
Engage the clamps.
Connect the connector.
for Front Pillar LH Side:
Engage the clamps.
Connect the 2 connectors.
63311C
2.INSTALL ROOF HEADLINING (for Panoramic Moon Roof)
|
Install in this Direction |
Insert the roof headlining into the cabin from the back door as shown in the illustration.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Engage the fasteners and guides to install the roof headlining.
| *a | Fastener | *b | Guide |
Install the 2 clips.
for Roof Rear Side:
Engage the guide.
Install the ground wire with the bolt.
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Windshield Glass Side:
Connect the 4 connectors.
for Front Pillar RH Side:
Engage the clamps.
Connect the connector.
for Front Pillar LH Side:
Engage the clamps.
Connect the 2 connectors.
63339A
3.INSTALL ROOF HEADLINING SERVICE HOLE COVER
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and claws to install the roof headlining service hole cover as shown in the illustration.
86466D
4.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
86466E
5.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
81340
6.INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)
81240J
7.INSTALL ROOM LIGHT ASSEMBLY (for TMC Made)
81260A
8.INSTALL MAP LIGHT ASSEMBLY
74612
9.INSTALL ASSIST GRIP COVER
Use the same procedure for all assist grip sub-assemblies.
Install the 2 assist grip covers and 2 clips to the assist grip sub-assembly.
74610A
10.INSTALL ASSIST GRIP SUB-ASSEMBLY
Use the same procedures for the opposite side.
|
Install in this Direction |
Engage the clips to install the assist grip sub-assembly as shown in the illustration.
74630E
11.INSTALL REAR ASSIST GRIP ASSEMBLY LH (w/ Assist Grip)
Use the same procedure as for the assist grip sub-assembly.
74620C
12.INSTALL REAR ASSIST GRIP ASSEMBLY RH (w/ Assist Grip)
Use the same procedure as for the assist grip sub-assembly.
13.INSTALL COAT HOOK (w/o Assist Grip)
Use the same procedures for the opposite side.
Engage the clip to install the coat hook.
74348C
14.INSTALL VISOR HOLDER
Use the same procedures for the opposite side.
|
Install in this Direction |
Engage the claws to install the base as shown in the illustration.
|
Install in this Direction |
Install the visor holder as shown in the illustration.
74320
15.INSTALL VISOR ASSEMBLY LH
74310
16.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
62472A
17.INSTALL ROOF SIDE INNER GARNISH LH
|
Install in this Direction |
Engage the clips to install the roof side inner garnish LH as shown in the illustration.
62471A
18.INSTALL ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
73370E
19.INSTALL REAR SEAT OUTER BELT ASSEMBLY LH
73360D
20.INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
64740C
21.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
|
Install in this Direction |
Engage the guide, clips and claws to install the deck trim side panel assembly LH as shown in the illustration.
Install the 2 screws.
64730B
22.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
64715C
23.INSTALL DECK TRIM SIDE COVER LH
Engage the guide and claw to install the deck trim side cover LH.
64714C
24.INSTALL DECK TRIM SIDE COVER RH
Use the same procedure as for the LH side.
71304C
25.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH
Install the rear seatback hinge sub-assembly LH with the bolt.
71303C
26.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
81330
27.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
64716D
28.INSTALL DECK TRIM REAR COVER
|
Install in this Direction |
Engage the guides and claws to install the deck trim rear cover as shown in the illustration.
62412B
29.INSTALL CENTER PILLAR UPPER GARNISH LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and clip to install the center pillar upper garnish LH as shown in the illustration.
Install the 2 clips.
62411B
30.INSTALL CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
62414A
31.INSTALL CENTER PILLAR LOWER GARNISH LH
|
Install in this Direction |
Engage the guides, claws and clips to install the center pillar lower garnish LH as shown in the illustration.
62413A
32.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
73220
33.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH
73210
34.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73233
35.INSTALL LAP BELT OUTER ANCHOR COVER
Use the same procedures for the opposite side.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for 5 Door)>INSTALLATION
62332A
36.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
62331A
37.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
67918F
38.INSTALL REAR DOOR SCUFF PLATE INSIDE LH
Engage the guides and claws to install the rear door scuff plate inside LH as shown in the illustration.
| *A | for HV Model | *B | for Gasoline Model |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
|
Install in this Direction (3) | - | - |
67917F
39.INSTALL REAR DOOR SCUFF PLATE INSIDE RH
Use the same procedure as for the LH side.
76974F
40.INSTALL REAR UNDER SIDE COVER LH (for HV Model)
|
Install in this Direction |
Engage the guides and clips to install the rear under side cover LH as shown in the illustration.
Install the clip.
76973F
41.INSTALL REAR UNDER SIDE COVER RH (for HV Model)
|
Install in this Direction |
Engage the guides and clips to install the rear under side cover RH as shown in the illustration.
Install the 2 clips.
62212
42.INSTALL FRONT PILLAR GARNISH LH
62211
43.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62312B
44.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
45.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62112
46.INSTALL COWL SIDE TRIM BOARD LH
|
Install in this Direction |
Engage the clip to install the cowl side trim board LH as shown in the illustration.
Install the clip.
62111C
47.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
67914B
48.INSTALL FRONT DOOR SCUFF PLATE LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and claws to install the front door scuff plate LH as shown in the illustration.
67913B
49.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
67914B
50.INSTALL FRONT DOOR SCUFF PLATE LH (w/ Plate)
Perform this procedure only when replacement of the front door scuff plate LH is necessary.
Remove the double-sided tape from the installation area of the front door scuff plate LH.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from the front door scuff plate LH.
After removing the release paper, keep the exposed adhesive free from foreign matter.
for Type A:
Install a new front door scuff plate LH as shown in the illustration.
| *a | View A | - | - |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 43 to 47 mm (1.69 to 1.85 in.) | b | 6.0 to 8.0 mm (0.236 to 0.315 in.) |
| c | 6.0 to 8.0 mm (0.236 to 0.315 in.) | - | - |
for Type B:
Install a new front door scuff plate LH as shown in the illustration.
| *a | View A | - | - |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 48 to 52 mm (1.89 to 2.05 in.) | b | 7.0 to 9.0 mm (0.276 to 0.354 in.) |
| c | 7.0 to 9.0 mm (0.276 to 0.354 in.) | - | - |
for Type C:
Install a new front door scuff plate LH as shown in the illustration.
| *a | View A | - | - |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 43 to 47 mm (1.69 to 1.85 in.) | b | 6.0 to 8.0 mm (0.236 to 0.315 in.) |
| c | 6.0 to 8.0 mm (0.236 to 0.315 in.) | - | - |
67913B
51.INSTALL FRONT DOOR SCUFF PLATE RH (w/ Plate)
Perform this procedure only when replacement of the front door scuff plate RH is necessary.
Use same procedure as for the LH side.
52.INSTALL REAR SEAT ASSEMBLY
64993
53.INSTALL REAR DECK FLOOR BOX (w/ Repair Kit)
Install the rear deck floor box with the clip.
64777J
54.INSTALL SPARE WHEEL CUSHION (for Compact Spare Tire)
Install the spare wheel cushion.
64771G
55.INSTALL SPARE WHEEL COVER
Install the spare wheel cover.
58410B
56.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
Install the deck board assembly.
64330D
57.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
|
Install in this Direction |
Engage the guides to install the package tray trim panel assembly as shown in the illustration.
Engage the hooks.