Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.04
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0475155 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  Reverse Signal Circuit  


DESCRIPTION

for M15A-FKS (for Manual Transaxle)

The radio and display receiver assembly receives a reverse signal from the back-up light switch assembly.


for M15A-FKS (for CVT)

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.


for M15A-FXE, 1KR-FE

The radio and display receiver assembly receives a reverse signal from the power distribution box assembly.


WIRING DIAGRAM

E463260E01
5.448,1.042 5.906,1.24 0.458,0.198 10 false REV 5.417,2.927 5.875,3.125 0.458,0.198 10 false H79 5.406,3.083 6.604,3.469 1.198,0.385 10 false Radio and Display Receiver Assembly 5.198,0.906 5.656,1.104 0.458,0.198 10 false 28 3.938,0.906 4.396,1.104 0.458,0.198 10 false 2 4.24,2.229 4.698,2.427 0.458,0.198 10 false *1 0.74,1.448 2.135,1.75 1.396,0.302 10 false 4C 1.396,2.115 3.906,2.406 2.51,0.292 10 false from Back-up Light Switch Assembly*3 0.979,2.469 4.188,2.844 3.208,0.375 10 false from Park/Neutral Position Switch Assembly*4 0.146,3.042 2.906,3.365 2.76,0.323 10 false *1: for M15A-FKS, 1KR-FE 0.125,3.375 2.031,3.646 1.906,0.271 10 false *2: for M15A-FXE 2.167,3.042 4.417,3.271 2.25,0.229 10 false *3: for Manual Transaxle 2.167,3.375 3.49,3.667 1.323,0.292 10 false *4: for CVT 0.74,1.594 3.729,1.833 2.99,0.24 10 false Power Distribution Box Assembly 4.208,1.115 4.667,1.313 0.458,0.198 10 false *2

PROCEDURE

1.CHECK BACK-UP LIGHT
a.

Move the shift lever to R and check if the back-up lights come on.

OK:

The back-up lights come on.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)

NG

2.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H79-28 (REV) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
H79-28 (REV) - Body ground Ignition switch ON
Shift lever not in R
Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the 4C power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H79-28 (REV) - 4C-2 Always Below 1 Ω
H79-28 (REV) or 4C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR