Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2021.04
RM36W0E _56 Audio / Visual / Telematics _091907 TELEMATICS _0434308 TELEMATICS SYSTEM(for eCall) J

TELEMATICS  TELEMATICS SYSTEM(for eCall)  Remote Engine Starter does not Operate  


WIRING DIAGRAM

E300171E53
1.552,0.896 2.167,1.094 0.615,0.198 10 false SLPD 2.052,0.76 2.667,0.958 0.615,0.198 10 false 30 4.927,0.76 5.542,0.958 0.615,0.198 10 false 11 5.219,0.885 5.833,1.083 0.615,0.198 10 false SLP 0.604,1.708 2.74,2 2.135,0.292 10 false Telematics Transceiver Assembly 4.719,1.573 6.531,1.958 1.813,0.385 10 false Certification ECU (Smart Key ECU Assembly) 4.729,1.406 5.344,1.604 0.615,0.198 10 false H46 0.594,1.531 1.208,1.729 0.615,0.198 10 false H85

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

Before replacing the telematics transceiver assembly or certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Check that the engine can be started by pressing the ignition switch.


Result:
Result Proceed to
Engine*1 or HV control system*2 can be started. A
Engine*1 or HV control system*2 cannot be started. B


*1: for Gasoline Model

*2: for HV Model



A

2.REGISTRATION

B

2.REGISTRATION
HINT:
If registration is not performed after replacing any of the following parts, the remote engine start and stop will not be available.
·

Certification ECU (smart key ECU assembly)

·

Telematics transceiver assembly



a.

Perform remote engine start and stop registration.

HINT:

Refer to Service Bulletin.



b.

Check if the problem symptom recurs.


Result:
Result Proceed to
System does not return to normal. A
System returns to normal. B



A

3.CHECK DTC

B

END

3.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B228562 is not output. A
DTC B228562 is output. B



A

4.CHECK TELEMATICS TRANSCEIVER ASSEMBLY

B

4.CHECK TELEMATICS TRANSCEIVER ASSEMBLY
a.
E432123C11
1.5,0.25 1.917,0.5 0.417,0.25 2.385,1.625 2.271,1.146 true 2.281,1.667 2.896,2.083 0.615,0.417 10 false SLPD 0.146,0.115 0.385,0.438 0.24,0.323 10 false *a 1.573,0.292 2.188,0.708 0.615,0.417 10 false H85
*a Front view of harness connector
(to Telematics Transceiver Assembly)


Disconnect the telematics transceiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H85-30 (SLPD) - Body ground Steering locked 11 to 14 V
Steering unlocked Below 1.5 V


HINT:

The steering locks when any door is opened with the shift lever in P and the ignition switch off. The steering unlocks when the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

REPLACE TELEMATICS TRANSCEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H85 telematics transceiver assembly connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-30 (SLPD) - H46-11 (SLP) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR