Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › from 2021.11
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432176 DIFFERENTIAL OIL SEAL A

C551 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission case oil seal and transaxle case oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF, TMMCZ Made:
(Click here)

PROCEDURE

Hide 2.REMOVE TRANSMISSION CASE OIL SEAL

a.
F100250E03
0.5,1.042 0.26,0.677 false 0.552,0.958 1,1.167 0.448,0.208 10 false SST

Using SST, remove the transmission case oil seal.

SST
09308-00010  


Hide 3.REMOVE TRANSAXLE CASE OIL SEAL

a.
F100251E03
2.885,1.063 2.75,0.708 false 2.938,1 3.396,1.208 0.458,0.208 10 false SST

Using SST, remove the transaxle case oil seal.

SST
09308-00010  


Hide 4.INSTALL TRANSMISSION CASE OIL SEAL

a.

Coat the lip of a new transmission case oil seal with MP grease.


b.
F100252C01
1.656,1.448 1.396,1.146 false 1.677,1.344 2.104,1.573 0.427,0.229 10 false SST 3.156,1.729 3.323,1.885 0.167,0.156 10 false *a
*a Depth


Using SST and a hammer, install the new transmission case oil seal.

SST
09316-60011  (09316-00011)

Standard depth:

2.1 to 3.1 mm (0.083 to 0.122 in.)


NOTICE:

Do not damage the oil seal lip.


NOTICE:
·
C381409C06
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the transmission case oil seal is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the transmission case oil seal.

·

Do not install the transmission case oil seal at an angle.

·

Do not remove the grease from the inner lip and outer lip of the transmission case oil seal.




Hide 5.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.
F100253C01
1.865,1.427 1.604,1.135 false 1.875,1.313 2.313,1.521 0.438,0.208 10 false SST 1.167,1.625 1.333,1.781 0.167,0.156 10 false *a
*a Depth


Using SST and a hammer, install the new transaxle case oil seal.

SST
09636-20010  

Standard depth:

1.7 to 2.7 mm (0.067 to 0.106 in.)


NOTICE:

Do not damage the oil seal lip.


NOTICE:
·
C381409C06
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the transmission case oil seal is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the transmission case oil seal.

·

Do not install the transmission case oil seal at an angle.

·

Do not remove the grease from the inner lip and outer lip of the transmission case oil seal.