Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › from 2021.11
RM36W0E _53 Suspension _087257 ALIGNMENT / HANDLING DIAGNOSIS _0417577 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment
w/ Active Torque Split AWD System:

ECU Data Initialization


Active torque split AWD system (Click here)
for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


·

for TMC Made:

(Click here)

·

for TMMF, TMMCZ Made:

(Click here)


for Gasoline Model:

Calibration


·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


·

for TMC Made:

(Click here)

·

for TMMF, TMMCZ Made:

(Click here)



PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT (except G16E-GTS)

NOTICE:
·

Before inspecting the wheel alignment, first inspect the vehicle height.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C427794E02
1.427,2.635 1.583,2.833 0.156,0.198 10 false B 0.385,2.531 0.563,2.698 0.177,0.167 10 false A 1.927,2.583 2.104,2.75 0.177,0.167 10 false D 3.094,2.563 3.271,2.729 0.177,0.167 10 false C

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center

B: Ground clearance of front lower No. 1 suspension arm bushing set bolt center

C: Ground clearance of rear wheel center

D: Ground clearance of rear axle beam bushing set bolt center


Vehicle Height (Unloaded Vehicle) (for TMC Made):
Engine Transaxle Tire Size Front A - B Rear C - D
M15A-FKS M/T 175/70R14 94 mm (3.70 in.) 24 mm (0.945 in.)
185/60R15 94 mm (3.70 in.) 25 mm (0.984 in.)
185/55R16 95 mm (3.74 in.) 24 mm (0.945 in.)
CVT 175/70R14 95 mm (3.74 in.) 25 mm (0.984 in.)
185/60R15 94 mm (3.70 in.) 25 mm (0.984 in.)
185/55R16 94 mm (3.70 in.) 24 mm (0.945 in.)
M15A-FXE - 175/70R14 95 mm (3.74 in.) 28 mm (1.10 in.)
185/60R15 96 mm (3.78 in.) 27 mm (1.06 in.)
185/55R16 96 mm (3.78 in.) 28 mm (1.10 in.)


Vehicle Height (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Front A - B Rear C - D
1KR-FE M/T 185/65R15
195/55R16
106 mm (4.17 in.) 35 mm (1.38 in.)
M15A-FKS M/T 185/65R15
195/55R16
205/45R17
108 mm (4.25 in.) 35 mm (1.38 in.)
CVT 185/65R15
195/55R16
205/45R17
108 mm (4.25 in.) 35 mm (1.38 in.)
M15A-FXE - 185/65R15
195/55R16
205/45R17
108 mm (4.25 in.) 37 mm (1.46 in.)


Vehicle Height (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Front A - B Rear C - D
1KR-FE M/T 185/65R15 86 mm (3.39 in.) 15 mm (0.591 in.)
M15A-FKS M/T 185/65R15 87 mm (3.43 in.) 15 mm (0.591 in.)
CVT 185/65R15 88 mm (3.46 in.) 15 mm (0.591 in.)
M15A-FXE - 185/65R15 88 mm (3.46 in.) 17 mm (0.669 in.)


Vehicle Height (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Front A - B Rear C - D
1KR-FE M/T 185/65R15 106 mm (4.17 in.) 35 mm (1.38 in.)
M15A-FKS M/T 185/65R15 108 mm (4.25 in.) 35 mm (1.38 in.)
CVT 185/65R15 108 mm (4.25 in.) 35 mm (1.38 in.)
M15A-FXE - 185/65R15 108 mm (4.25 in.) 37 mm (1.46 in.)



Hide 3.MEASURE VEHICLE HEIGHT (for G16E-GTS)

NOTICE:
·

Before inspecting the wheel alignment, first inspect the vehicle height.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C456352E01
0.302,2.625 0.458,2.823 0.156,0.198 10 false A 1.281,2.708 1.438,2.906 0.156,0.198 10 false B 2.042,2.635 2.198,2.833 0.156,0.198 10 false C 3.031,2.677 3.188,2.875 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center

B: Ground clearance of front lower No. 1 suspension arm bushing set bolt center

C: Ground clearance of rear wheel center

D: Ground clearance of rear No. 2 suspension arm assembly set bolt center


Vehicle Height (Unloaded Vehicle):
Engine Transaxle Tire Size Front A - B Rear C - D

*1: w/ Brake Air Duct

*2: w/o Brake Air Duct

G16E-GTS M/T 225/40R18 136 mm (5.35 in.)*1
135 mm (5.31 in.)*2
65 mm (2.56 in.)



Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C12
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.74 2.99,0.917 0.229,0.177 10 *b 0.458,0.625 0.698,0.802 0.24,0.177 10 *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
M15A-FKS M/T 175/70R14
185/60R15
185/55R16
-0°06' +/- 0°45' (-0.10° +/- 0.75°) 0°45' (0.75°) or less
CVT 175/70R14
185/60R15
185/55R16
-0°06' +/- 0°45' (-0.10° +/- 0.75°)
M15A-FXE - 175/70R14
185/60R15
185/55R16
-0°07' +/- 0°45' (-0.12° +/- 0.75°)


Caster (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Caster Inclination Right-left Difference
M15A-FKS M/T 175/70R14
185/60R15
5°05' +/- 0°45' (5.08° +/- 0.75°) 0°45' (0.75°) or less
185/55R16 5°06' +/- 0°45' (5.10° +/- 0.75°)
CVT 175/70R14
185/60R15
185/55R16
5°05' +/- 0°45' (5.08° +/- 0.75°)
M15A-FXE - 175/70R14
185/60R15
5°08' +/- 0°45' (5.13° +/- 0.75°)
185/55R16 5°06' +/- 0°45' (5.10° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Steering Axis Inclination Reference
M15A-FKS M/T 175/70R14
185/60R15
185/55R16
13°02' (13.03°)
CVT 175/70R14
185/60R15
185/55R16
13°02' (13.03°)
M15A-FXE - 175/70R14
185/60R15
185/55R16
13°04' (13.07°)


Camber (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
G16E-GTS M/T 225/40R18 -1°23' +/- 0°45' (-1.38° +/- 0.75°) 0°45' (0.75°) or less


Caster (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Caster Inclination Right-left Difference

*1: w/ Brake Air Duct

*2: w/o Brake Air Duct

G16E-GTS M/T 225/40R18 6°04' +/- 0°45' (6.07° +/- 0.75°)*1
6°03' +/- 0°45' (6.05° +/- 0.75°)*2
0°45' (0.75°) or less


Steering Axis Inclination (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Steering Axis Inclination Reference

*1: w/ Brake Air Duct

*2: w/o Brake Air Duct

G16E-GTS M/T 225/40R18 14°34' (14.57°)*1
14°33' (14.55°)*2


Camber (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°) 0°45' (0.75°) or less
195/55R16 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
M15A-FKS M/T 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
195/55R16
205/45R17
-0°16' +/- 0°45' (-0.27° +/- 0.75°)
CVT 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
195/55R16
205/45R17
-0°16' +/- 0°45' (-0.27° +/- 0.75°)
M15A-FXE - 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
195/55R16
205/45R17
-0°16' +/- 0°45' (-0.27° +/- 0.75°)


Caster (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Caster Inclination Right-left Difference
1KR-FE M/T 185/65R15
195/55R16
6°03' +/- 0°45' (6.05° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15
195/55R16
6°00' +/- 0°45' (6.00° +/- 0.75°)
205/45R17 6°01' +/- 0°45' (6.02° +/- 0.75°)
CVT 185/65R15 5°58' +/- 0°45' (5.97° +/- 0.75°)
195/55R16 6°00' +/- 0°45' (6.00° +/- 0.75°)
205/45R17 6°01' +/- 0°45' (6.02° +/- 0.75°)
M15A-FXE - 185/65R15
195/55R16
6°03' +/- 0°45' (6.05° +/- 0.75°)
205/45R17 6°04' +/- 0°45' (6.07° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Steering Axis Inclination Reference
1KR-FE M/T 185/65R15 15°00' (15.00°)
195/55R16 14°59' (14.98°)
M15A-FKS M/T 185/65R15
195/55R16
205/45R17
15°03' (15.05°)
CVT 185/65R15
195/55R16
205/45R17
15°03' (15.05°)
M15A-FXE - 185/65R15
195/55R16
205/45R17
15°03' (15.05°)


Camber (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 0°06' +/- 0°45' (0.10° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15 0°04' +/- 0°45' (0.07° +/- 0.75°)
CVT 185/65R15 0°04' +/- 0°45' (0.07° +/- 0.75°)
M15A-FXE - 185/65R15 0°04' +/- 0°45' (0.07° +/- 0.75°)


Caster (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Caster Inclination Right-left Difference
1KR-FE M/T 185/65R15 5°46' +/- 0°45' (5.77° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15 5°44' +/- 0°45' (5.73° +/- 0.75°)
CVT 185/65R15 5°43' +/- 0°45' (5.72° +/- 0.75°)
M15A-FXE - 185/65R15 5°47' +/- 0°45' (5.78° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Steering Axis Inclination Reference
1KR-FE M/T 185/65R15 14°27' (14.45°)
M15A-FKS M/T 185/65R15 14°30' (14.50°)
CVT 185/65R15 14°30' (14.50°)
M15A-FXE - 185/65R15 14°30' (14.50°)


Camber (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
CVT 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
M15A-FXE - 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)


Caster (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Caster Inclination Right-left Difference
1KR-FE M/T 185/65R15 6°03' +/- 0°45' (6.05° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15 6°00' +/- 0°45' (6.00° +/- 0.75°)
CVT 185/65R15 5°58' +/- 0°45' (5.97° +/- 0.75°)
M15A-FXE - 185/65R15 6°03' +/- 0°45' (6.05° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Steering Axis Inclination Reference
1KR-FE M/T 185/65R15 14°27' (14.45°)
M15A-FKS M/T 185/65R15 14°30' (14.50°)
CVT 185/65R15 14°30' (14.50°)
M15A-FXE - 185/65R15 14°30' (14.50°)



Hide 5.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL


b.
C427796

Remove the 2 nuts on the lower side of the front shock absorber.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber, clean the installation surfaces of the front shock absorber and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C148065N13
0.719,0.25 1.177,0.448 0.458,0.198 10 false (-) 2.073,0.26 2.531,0.458 0.458,0.198 10 false (+)

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


f.
C427796

Tighten the 2 nuts.

NOTICE:

Keep the bolts from rotating when tightening the nuts.


Torque:
for TMC Made except G16E-GTS : 164 N*m (1672 kgf*cm, 121 ft.*lbf)
for TMC Made G16E-GTS : 270 N*m (2753 kgf*cm, 199 ft.*lbf)
for TMMF, TMMCZ Made : 240 N*m (2447 kgf*cm, 177 ft.*lbf)


g.

Install the front wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>INSTALLATION


h.

Bounce the vehicle up and down at the corners to stabilize the suspension.


i.

Check the camber.

Camber (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
M15A-FKS M/T 175/70R14
185/60R15
185/55R16
-0°06' +/- 0°45' (-0.10° +/- 0.75°) 0°45' (0.75°) or less
CVT 175/70R14
185/60R15
185/55R16
-0°06' +/- 0°45' (-0.10° +/- 0.75°)
M15A-FXE - 175/70R14
185/60R15
185/55R16
-0°07' +/- 0°45' (-0.12° +/- 0.75°)


Camber (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
G16E-GTS M/T 225/40R18 -1°23' +/- 0°45' (-1.38° +/- 0.75°) 0°45' (0.75°) or less


Camber (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°) 0°45' (0.75°) or less
195/55R16 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
M15A-FKS M/T 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
195/55R16
205/45R17
-0°16' +/- 0°45' (-0.27° +/- 0.75°)
CVT 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
195/55R16
205/45R17
-0°16' +/- 0°45' (-0.27° +/- 0.75°)
M15A-FXE - 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
195/55R16
205/45R17
-0°16' +/- 0°45' (-0.27° +/- 0.75°)


Camber (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 0°06' +/- 0°45' (0.10° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15 0°04' +/- 0°45' (0.07° +/- 0.75°)
CVT 185/65R15 0°04' +/- 0°45' (0.07° +/- 0.75°)
M15A-FXE - 185/65R15 0°04' +/- 0°45' (0.07° +/- 0.75°)


Camber (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°) 0°45' (0.75°) or less
M15A-FKS M/T 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
CVT 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)
M15A-FXE - 185/65R15 -0°15' +/- 0°45' (-0.25° +/- 0.75°)


i.
C404820N01
1.51,3.417 1.708,3 1.708,3 1.927,3 false 1.51,3.698 1.708,3.281 1.708,3.281 1.927,3.281 false 1.99,2.917 2.167,3.135 0.177,0.219 11 false 1 2,3.188 2.177,3.406 0.177,0.219 11 false 2

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:
·

Try to adjust the camber to the center of the specified values.

·

The bolts can be inserted from either direction, but insert all the bolts from the same direction.



To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

NOTICE:

Replace the nut with a new one when replacing the bolt.



ii.

Table (1) (To move the axle hub toward the positive side)

C212217C01
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 2.521,0.792 2.75,0.99 0.229,0.198 10 *c 3.219,1.406 3.448,1.594 0.229,0.188 10 *d 5.979,0.792 6.198,0.99 0.219,0.198 10 *e 5.271,0.792 5.521,0.99 0.25,0.198 10 *d 4.604,1.406 4.781,1.583 0.177,0.177 10 *f 3.917,1.406 4.125,1.615 0.208,0.208 10 *e 4.396,6.375 4.583,6.552 0.188,0.177 10 *f 5.969,1.396 6.177,1.552 0.208,0.156 10 *f 5.271,1.406 5.469,1.583 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.646,0.792 6.854,0.969 0.208,0.177 10 *f 2.542,2.99 2.719,3.219 0.177,0.229 10 A 2.542,4.188 2.771,4.406 0.229,0.219 10 F 2.542,3.469 2.771,3.688 0.229,0.219 10 C 2.542,3.938 2.74,4.156 0.198,0.219 10 E 2.542,3.24 2.729,3.448 0.188,0.208 10 B 2.542,3.708 2.729,3.927 0.188,0.219 10 D 3.927,3.01 4.177,3.24 0.25,0.229 10 C 5.271,3 5.51,3.229 0.24,0.229 10 E 3.229,3.01 3.406,3.219 0.177,0.208 10 B 4.604,3 4.792,3.24 0.188,0.24 10 D 3.229,2.76 3.448,2.99 0.219,0.229 10 G 3.229,3.24 3.406,3.448 0.177,0.208 10 C 3.229,3.708 3.448,3.938 0.219,0.229 10 E 3.229,3.469 3.427,3.698 0.198,0.229 10 D 3.229,3.938 3.427,4.167 0.198,0.229 10 F 3.927,2.51 4.115,2.74 0.188,0.229 10 G 3.927,2.76 4.135,2.969 0.208,0.208 10 A 3.927,3.708 4.115,3.938 0.188,0.229 10 F 3.917,3.469 4.083,3.688 0.167,0.219 10 E 3.927,3.24 4.135,3.458 0.208,0.219 10 D 4.604,2.281 4.802,2.531 0.198,0.25 10 G 6.656,1.563 6.833,1.823 0.177,0.26 10 G 5.979,1.813 6.26,2.063 0.281,0.25 10 G 5.271,2.031 5.458,2.281 0.188,0.25 10 G 6.656,1.813 6.813,2.042 0.156,0.229 10 A 6.656,2.281 6.844,2.531 0.188,0.25 10 C 6.656,2.76 6.885,3.01 0.229,0.25 10 E 6.656,2.031 6.833,2.26 0.177,0.229 10 B 6.656,2.51 6.875,2.781 0.219,0.271 10 D 5.979,2.031 6.177,2.292 0.198,0.26 10 A 5.979,2.51 6.188,2.75 0.208,0.24 10 C 5.979,2.281 6.26,2.531 0.281,0.25 10 B 5.979,2.76 6.167,2.99 0.188,0.229 10 D 5.979,3 6.115,3.208 0.135,0.208 10 F 5.271,3.24 5.49,3.448 0.219,0.208 10 F 5.271,2.281 5.406,2.51 0.135,0.229 10 A 5.271,2.76 5.448,2.969 0.177,0.208 10 C 5.271,2.51 5.438,2.74 0.167,0.229 10 B 4.604,2.51 4.781,2.76 0.177,0.25 10 A 4.604,2.76 4.781,2.969 0.177,0.208 10 B 4.604,3.24 4.813,3.458 0.208,0.219 10 E 4.604,3.469 4.813,3.698 0.208,0.229 10 F 1.625,5.073 1.76,5.281 0.135,0.208 10 A 5.094,5.073 5.229,5.281 0.135,0.208 10 F 3.052,5.073 3.188,5.281 0.135,0.208 10 C 4.406,5.073 4.542,5.281 0.135,0.208 10 E 2.344,5.073 2.479,5.281 0.135,0.208 10 B 3.729,5.073 3.865,5.281 0.135,0.208 10 D 5.802,5.073 5.938,5.281 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 3.042,6.375 3.229,6.531 0.188,0.156 10 *f 3.719,6.375 3.958,6.542 0.24,0.167 10 *f 5.083,6.375 5.292,6.573 0.208,0.198 10 *f 5.094,5.75 5.292,5.917 0.198,0.167 10 *f 4.385,5.75 4.604,5.917 0.219,0.167 10 *e 2.333,6.375 2.542,6.542 0.208,0.167 10 *e 1.625,6.375 1.854,6.552 0.229,0.177 10 *d 3.719,5.75 3.927,5.938 0.208,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.75 1.844,5.948 0.219,0.198 10 *c 2.333,5.75 2.521,5.906 0.188,0.156 10 *c 5.802,6.365 6.021,6.563 0.219,0.198 10 *c 5.76,5.76 5.969,5.948 0.208,0.188 10 *c 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 *c 3.219,0.792 3.448,0.969 0.229,0.177 10 *c 3.917,0.792 4.135,1.01 0.219,0.219 10 *c 4.604,0.792 4.823,1.01 0.219,0.219 10 *c 5.979,3 6.24,3.24 0.26,0.24 10 F 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.198,5.021 0.323,0.229 12 *B 0.063,0.135 0.333,0.333 0.271,0.198 12 *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d for TMC Made except G16E-GTS: 90109-15002
for TMMF, TMMCZ Made, TMC Made G16E-GTS: 90105-17013
*e for TMC Made except G16E-GTS: 90109-15003
for TMMF, TMMCZ Made, TMC Made G16E-GTS: 90105-17014
*f for TMC Made except G16E-GTS: 90109-15004
for TMMF, TMMCZ Made, TMC Made G16E-GTS: 90105-17015



iii.

Table (2) (To move the axle hub toward the negative side)

C212218C01
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 1.635,5.052 1.771,5.26 0.135,0.208 10 A 5.094,5.052 5.229,5.26 0.135,0.208 10 F 3.052,5.052 3.188,5.26 0.135,0.208 10 C 4.406,5.052 4.542,5.26 0.135,0.208 10 E 2.344,5.052 2.479,5.26 0.135,0.208 10 B 3.729,5.052 3.865,5.26 0.135,0.208 10 D 5.802,5.052 5.938,5.26 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.167,5.021 0.292,0.229 12 *B 0.063,0.135 0.417,0.354 0.354,0.219 12 *A 5.292,2.76 5.427,2.969 0.135,0.208 10 E 5.292,3.708 5.427,3.917 0.135,0.208 10 G 5.292,2.521 5.427,2.729 0.135,0.208 10 F 5.292,3.469 5.427,3.677 0.135,0.208 10 A 5.292,3 5.427,3.208 0.135,0.208 10 C 5.292,3.24 5.427,3.448 0.135,0.208 10 B 2.542,2.76 2.677,2.969 0.135,0.208 10 A 2.542,1.563 2.677,1.771 0.135,0.208 10 F 2.542,2.281 2.677,2.49 0.135,0.208 10 C 2.542,1.813 2.677,2.021 0.135,0.208 10 E 2.542,2.521 2.677,2.729 0.135,0.208 10 B 2.542,2.031 2.677,2.24 0.135,0.208 10 D 3.229,2.76 3.365,2.969 0.135,0.208 10 B 3.229,3 3.365,3.208 0.135,0.208 10 G 3.229,2.521 3.365,2.729 0.135,0.208 10 C 3.229,2.031 3.365,2.24 0.135,0.208 10 E 3.229,2.281 3.365,2.49 0.135,0.208 10 D 3.229,1.813 3.375,2.021 0.146,0.208 10 F 3.927,2.76 4.063,2.969 0.135,0.208 10 C 3.927,3.24 4.063,3.448 0.135,0.208 10 G 3.927,3 4.063,3.208 0.135,0.208 10 A 3.927,2.031 4.063,2.24 0.135,0.208 10 F 3.927,2.281 4.063,2.49 0.135,0.208 10 E 3.927,2.521 4.063,2.729 0.135,0.208 10 D 4.604,2.76 4.74,2.969 0.135,0.208 10 D 4.604,3.469 4.74,3.677 0.135,0.208 10 G 4.604,3.24 4.74,3.448 0.135,0.208 10 A 4.604,3 4.74,3.208 0.135,0.208 10 B 4.604,2.521 4.74,2.729 0.135,0.208 10 E 4.604,2.281 4.74,2.49 0.135,0.208 10 F 5.99,3.938 6.125,4.146 0.135,0.208 10 G 5.99,3.708 6.125,3.917 0.135,0.208 10 A 5.99,3.24 6.125,3.448 0.135,0.208 10 C 5.99,3.469 6.125,3.677 0.135,0.208 10 B 5.99,3 6.125,3.208 0.135,0.208 10 D 5.99,2.76 6.125,2.969 0.135,0.208 10 F 6.688,4.188 6.823,4.396 0.135,0.208 10 G 6.688,3.938 6.823,4.146 0.135,0.208 10 A 6.688,3.469 6.823,3.677 0.135,0.208 10 C 6.688,3 6.823,3.208 0.135,0.208 10 E 6.688,3.708 6.823,3.917 0.135,0.208 10 B 6.688,3.24 6.823,3.448 0.135,0.208 10 D 2.51,0.792 2.729,0.969 0.219,0.177 10 *c 3.219,1.396 3.406,1.573 0.188,0.177 10 *d 5.969,0.781 6.115,0.938 0.146,0.156 10 *e 5.271,0.792 5.469,0.979 0.198,0.188 10 *d 4.604,1.396 4.781,1.573 0.177,0.177 10 *f 3.906,1.396 4.083,1.573 0.177,0.177 10 *e 5.979,1.396 6.188,1.552 0.208,0.156 10 *f 5.281,1.396 5.479,1.573 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.656,0.792 6.823,0.958 0.167,0.167 10 *f 2.51,1.396 2.688,1.573 0.177,0.177 10 *c 3.219,0.792 3.396,0.948 0.177,0.156 10 *c 3.927,0.792 4.115,0.979 0.188,0.188 10 *c 4.604,0.792 4.781,0.958 0.177,0.167 10 *c 4.385,6.375 4.531,6.531 0.146,0.156 10 *f 3.01,6.375 3.198,6.531 0.188,0.156 10 *f 3.708,6.375 3.948,6.542 0.24,0.167 10 *f 5.094,6.375 5.302,6.573 0.208,0.198 10 *f 5.083,5.75 5.271,5.906 0.188,0.156 10 *f 4.375,5.75 4.573,5.906 0.198,0.156 10 *e 2.313,6.375 2.521,6.542 0.208,0.167 10 *e 1.625,6.375 1.771,6.531 0.146,0.156 10 *d 3.688,5.75 3.875,5.938 0.188,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.74 1.802,5.927 0.177,0.188 10 *c 2.323,5.75 2.5,5.906 0.177,0.156 10 *c 5.781,6.375 5.969,6.542 0.188,0.167 10 *c 5.771,5.75 5.979,5.938 0.208,0.188 10 *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d for TMC Made except G16E-GTS: 90109-15002
for TMMF, TMMCZ Made, TMC Made G16E-GTS: 90105-17013
*e for TMC Made except G16E-GTS: 90109-15003
for TMMF, TMMCZ Made, TMC Made G16E-GTS: 90105-17014
*f for TMC Made except G16E-GTS: 90109-15004
for TMMF, TMMCZ Made, TMC Made G16E-GTS: 90105-17015




j.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step A, replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 6.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N (for CVT, Hybrid Transaxle).


c.

Release the parking brake and move the shift lever to neutral (for Manual Transaxle).


d.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


e.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


f.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



g.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Specified Condition
M15A-FKS M/T 175/70R14 C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.7 +/- 2.0 mm (0.106 +/- 0.0787 in.)
185/60R15
185/55R16
C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
CVT 175/70R14 C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.7 +/- 2.0 mm (0.106 +/- 0.0787 in.)
185/60R15
185/55R16
C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
M15A-FXE - 175/70R14
185/60R15
185/55R16
C + D: 0°15' +/- 0°11' (0.25° +/- 0.19°)
B - A: 2.6 +/- 2.0 mm (0.102 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Specified Condition

*1: w/ Brake Air Duct

*2: w/o Brake Air Duct

G16E-GTS M/T 225/40R18 C + D: 0°08' +/- 0°11' (0.14° +/- 0.18°)*1
C + D: 0°10' +/- 0°11' (0.16° +/- 0.18°)*2
B - A: 1.6 +/- 2.0 mm (0.0630 +/- 0.0787 in.)*1
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)*2


Toe-in (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°18' +/- 0°11' (0.3° +/- 0.19°)
B - A: 3.2 +/- 2.0 mm (0.126 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.29° +/- 0.19°)
B - A: 3.1 +/- 2.0 mm (0.122 +/- 0.0787 in.)
M15A-FKS M/T 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
205/45R17 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
CVT 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
205/45R17 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
M15A-FXE - 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
205/45R17 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°12' +/- 0°11' (0.21° +/- 0.19°)
B - A: 2.3 +/- 2.0 mm (0.0906 +/- 0.0787 in.)
M15A-FKS M/T 185/65R15 C + D: 0°11' +/- 0°11' (0.19° +/- 0.19°)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)
CVT 185/65R15 C + D: 0°11' +/- 0°11' (0.19° +/- 0.19°)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)
M15A-FXE - 185/65R15 C + D: 0°11' +/- 0°11' (0.19° +/- 0.19°)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°18' +/- 0°11' (0.3° +/- 0.19°)
B - A: 3.2 +/- 2.0 mm (0.126 +/- 0.0787 in.)
M15A-FKS M/T 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
CVT 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
M15A-FXE - 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 7.ADJUST TOE-IN

a.

Separate the steering rack boot clips from the steering rack boot.


b.
C428503

Loosen the tie rod end lock nuts.


c.
C317577C23
1.625,0.51 1.781,0.708 0.156,0.198 10 false A 1.667,1.365 1.823,1.563 0.156,0.198 10 false B 1.031,0.323 1.188,0.521 0.156,0.198 10 false C 2.208,0.344 2.365,0.542 0.156,0.198 10 false D
V100135

Front of the Vehicle


Turn the right and left steering rack ends by an equal amount to adjust the toe-in.

HINT:
·

If the toe-in measurement is more than the specified range, shorten the left and right steering rack ends until the measurement is within the specified range.

·

If the toe-in measurement is less than the specified range, extend the left and right steering rack ends until the measurement is within the specified range.



Toe-in (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Specified Condition
M15A-FKS M/T 175/70R14 C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.7 +/- 2.0 mm (0.106 +/- 0.0787 in.)
185/60R15
185/55R16
C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
CVT 175/70R14 C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.7 +/- 2.0 mm (0.106 +/- 0.0787 in.)
185/60R15
185/55R16
C + D: 0°16' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
M15A-FXE - 175/70R14 C + D: 0°15' +/- 0°11' (0.25° +/- 0.19°)
B - A: 2.6 +/- 2.0 mm (0.102 +/- 0.0787 in.)
185/60R15
185/55R16
C + D: 0°15' +/- 0°11' (0.25° +/- 0.19°)
B - A: 2.6 +/- 2.0 mm (0.102 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Specified Condition

*1: w/ Brake Air Duct

*2: w/o Brake Air Duct

G16E-GTS M/T 225/40R18 C + D: 0°08' +/- 0°11' (0.14° +/- 0.18°)*1
C + D: 0°10' +/- 0°11' (0.16° +/- 0.18°)*2
B - A: 1.6 +/- 2.0 mm (0.0630 +/- 0.0787 in.)*1
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)*2


Toe-in (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°18' +/- 0°11' (0.3° +/- 0.19°)
B - A: 3.2 +/- 2.0 mm (0.126 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.29° +/- 0.19°)
B - A: 3.1 +/- 2.0 mm (0.122 +/- 0.0787 in.)
M15A-FKS M/T 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
205/45R17 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
CVT 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
205/45R17 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
M15A-FXE - 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
195/55R16 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
205/45R17 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°12' +/- 0°11' (0.21° +/- 0.19°)
B - A: 2.3 +/- 2.0 mm (0.0906 +/- 0.0787 in.)
M15A-FKS M/T 185/65R15 C + D: 0°11' +/- 0°11' (0.19° +/- 0.19°)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)
CVT 185/65R15 C + D: 0°11' +/- 0°11' (0.19° +/- 0.19°)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)
M15A-FXE - 185/65R15 C + D: 0°11' +/- 0°11' (0.19° +/- 0.19°)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°18' +/- 0°11' (0.3° +/- 0.19°)
B - A: 3.2 +/- 2.0 mm (0.126 +/- 0.0787 in.)
M15A-FKS M/T 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
CVT 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)
M15A-FXE - 185/65R15 C + D: 0°17' +/- 0°11' (0.26° +/- 0.19°)
B - A: 2.8 +/- 2.0 mm (0.110 +/- 0.0787 in.)


HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.



d.

Tighten the tie rod end sub-assembly lock nuts.


ii.

for RH side:

HINT:

Perform the same procedure as for the LH side.




e.

Place the steering rack boots on the seats and install the steering rack boot clips.


ii.

for RH side:

HINT:

Perform the same procedure as for the LH side.




Hide 8.INSPECT WHEEL ANGLE

a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle) (for TMC Made except G16E-GTS):
Engine Transaxle Tire Size Inside Wheel Outside Wheel
M15A-FKS M/T 175/70R14 42°40' +/- 2°00' (42.67° +/- 2.00°) 35°30' (35.50°)
185/60R15
185/55R16
39°20' +/- 2°00' (39.33° +/- 2.00°) 33°37' (33.62°)
CVT 175/70R14 42°40' +/- 2°00' (42.67° +/- 2.00°) 35°30' (35.50°)
185/60R15
185/55R16
39°20' +/- 2°00' (39.33° +/- 2.00°) 33°37' (33.62°)
M15A-FXE - 175/70R14 42°38' +/- 2°00' (42.63° +/- 2.00°) 35°28' (35.47°)
185/60R15 39°18' +/- 2°00' (39.30° +/- 2.00°) 33°34' (33.57°)
185/55R16 39°18' +/- 2°00' (39.30° +/- 2.00°) 33°35' (33.58°)


Wheel Turning Angle (Unloaded Vehicle) (for TMC Made G16E-GTS):
Engine Transaxle Tire Size Inside Wheel Outside Wheel

*1: w/ Brake Air Duct

*2: w/o Brake Air Duct

G16E-GTS M/T 225/40R18 37°44' +/- 2°00' (37.73° +/- 2.00°)*1
37°46' +/- 2°00' (37.77° +/- 2.00°)*2
31°5' (31.08°)*1
31°6' (31.10°)*2


Wheel Turning Angle (Unloaded Vehicle) (for TMMF, TMMCZ Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Inside Wheel Outside Wheel
1KR-FE M/T 185/65R15 41°51' +/- 2°00' (41.85° +/- 2.00°) 34°25' (34.42°)
195/55R16 38°33' +/- 2°00' (38.55° +/- 2.00°) 32°37' (32.62°)
M15A-FKS M/T 185/65R15 41°48' +/- 2°00' (41.80° +/- 2.00°) 34°22' (34.37°)
195/55R16
205/45R17
38°30' +/- 2°00' (38.50° +/- 2.00°) 32°34' (32.57°)
CVT 185/65R15 41°48' +/- 2°00' (41.80° +/- 2.00°) 34°22' (34.37°)
195/55R16
205/45R17
38°30' +/- 2°00' (38.50° +/- 2.00°) 32°34' (32.57°)
M15A-FXE - 185/65R15 41°48' +/- 2°00' (41.80° +/- 2.00°) 34°22' (34.37°)
195/55R16
205/45R17
38°30' +/- 2°00' (38.50° +/- 2.00°) 32°34' (32.57°)


Wheel Turning Angle (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Inside Wheel Outside Wheel
1KR-FE M/T 185/65R15 42°47' +/- 2°00' (42.78° +/- 2.00°) 34°85' (35.42°)
M15A-FKS M/T 185/65R15 42°43' +/- 2°00' (42.72° +/- 2.00°) 34°79' (35.32°)
CVT 185/65R15 42°43' +/- 2°00' (42.72° +/- 2.00°) 34°79' (35.32°)
M15A-FXE - 185/65R15 42°43' +/- 2°00' (42.72° +/- 2.00°) 34°79' (35.32°)


Wheel Turning Angle (Unloaded Vehicle) (for TMMF, TMMCZ Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Inside Wheel Outside Wheel
1KR-FE M/T 185/65R15 41°51' +/- 2°00' (41.85° +/- 2.00°) 34°25' (34.42°)
M15A-FKS M/T 185/65R15 41°48' +/- 2°00' (41.80° +/- 2.00°) 34°22' (34.37°)
CVT 185/65R15 41°48' +/- 2°00' (41.80° +/- 2.00°) 34°22' (34.37°)
M15A-FXE - 185/65R15 41°48' +/- 2°00' (41.80° +/- 2.00°) 34°22' (34.37°)


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.


Hide 9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 10.INSPECT AND ADJUST HEADLIGHT AIMING

HINT:

These procedures are to be performed when suspension or tires components have been removed or replaced.



Hide 12.PERFORM ECU DATA INITIALIZATION (w/ Active Torque Split AWD System)