Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › from 2021.11
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0417588 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the steering knuckle removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for TMC Made HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF, TMMCZ Made:
(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF, TMMCZ Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:
for TMC Made HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY (for TMC Made G16E-GTS)

Hide 2.REMOVE FRONT AXLE ASSEMBLY (for TMC Made except G16E-GTS)

Hide 3.REMOVE FRONT AXLE ASSEMBLY (for TMMF, TMMCZ Made)

Hide 43340A 4.REMOVE FRONT LOWER BALL JOINT ASSEMBLY (for TMC Made G16E-GTS)

Hide 43340A 5.REMOVE FRONT LOWER BALL JOINT ASSEMBLY (for TMMF, TMMCZ Made)

Hide 43212 6.REMOVE STEERING KNUCKLE (for TMC Made G16E-GTS)

a.
C445870

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.




Hide 43212 7.REMOVE STEERING KNUCKLE (for TMC Made except G16E-GTS)

a.
C428606

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Using a 12 mm hexagon socket wrench, remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.




Hide 43212 8.REMOVE STEERING KNUCKLE (for TMMF, TMMCZ Made)

a.
C436146

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.