Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT › from 2020.09
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0431059 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
except G16E-GTS:
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C427869

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C427870

Remove the cotter pin.


c.

Remove the nut.


d.
C428506C03
0.75,0.219 1,0.219 1,0.219 1,1.073 true 0.875,1.052 0.875,0.229 true 3.042,0.896 3.24,1.094 0.198,0.198 10 false *a 0.448,0.135 0.781,0.333 0.333,0.198 10 false SST
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



e.
C428507C03
1.74,1.865 1.948,1.656 1.948,1.656 2.188,1.656 false 2.083,2.76 2.719,2.063 2.719,2.063 2.823,2.063 true 0.927,4.344 1.042,4.344 1.042,4.344 1.146,4.031 false 1.542,1.24 1.99,1.24 false 0.74,4.24 1.052,4.396 0.313,0.156 10 false *a 2.385,0.646 2.698,0.802 0.313,0.156 10 false *b 1.385,1.146 1.698,1.302 0.313,0.156 10 false *c 2.875,1.969 3.188,2.125 0.313,0.156 10 false *d 2.396,0.271 2.708,0.427 0.313,0.156 10 false *b 2.25,1.573 2.563,1.729 0.313,0.156 10 false SST 2.01,3.469 2.323,3.625 0.313,0.156 10 false A 2.01,3.76 2.323,3.917 0.313,0.156 10 false B
*a Center Nut
*b Molybdenum Grease Application Area
*c Place wrench here
*d String
V113147

Turn


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.