Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD › from 2021.11
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0421927 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced the during antenna cord sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B473126

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 55302C 1.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55971C 2.REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT

Hide 55972C 3.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Hide 86101 4.REMOVE ANTENNA CORD SUB-ASSEMBLY

a.

for Separate Type:

i.

Disengage the claws. (for LHD)

E451694C01
5.813,2.594 6.823,1.99 6.823,1.99 6.49,2.313 true 3.427,1.333 2.427,1.271 2.427,1.271 3.427,2.396 true 6.302,3.135 6.51,3.479 false 4.25,2.781 3.927,3.458 3.927,3.458 5.49,3.042 true 4.427,1.74 4.917,1.417 4.917,1.417 4.219,2.292 true 4.469,2.313 4.917,1.427 true 6.563,3.417 6.865,3.667 0.302,0.25 10 false *b 6.844,1.885 7.073,2.323 0.229,0.438 10 true *a 4.948,1.271 5.229,1.583 0.281,0.313 10 false *a 3.729,3.417 3.979,3.656 0.25,0.24 10 false *a 2.26,1.156 2.542,1.406 0.281,0.25 10 false *a
*a Clamp *b Guide



ii.

Disconnect the connector.


iii.

Disengage the clamps and guides to remove the antenna cord sub-assembly.


iv.

Disengage the claws. (for RHD)

E451695C01
3.385,2.771 4.146,2.438 4.146,2.438 3.927,3.031 true 2.833,2.271 3.625,2.198 3.625,2.198 2.844,2.521 true 6.219,3.135 6.427,3.438 false 4.896,2.802 4.938,3.51 4.938,3.51 5.583,3.021 true 2.802,1.656 2.24,1.135 2.24,1.135 2.875,2.083 true 3,1.219 2.25,1.146 true 6.469,3.448 6.781,3.604 0.313,0.156 10 false *b 4.198,2.302 4.396,2.521 0.198,0.219 10 true *a 3.667,2.104 3.979,2.26 0.313,0.156 10 false *a 4.844,3.51 5.104,3.74 0.26,0.229 10 false *a 2.052,1.021 2.365,1.177 0.313,0.156 10 false *a
*a Clamp *b Guide



v.

Disconnect the connector.


vi.

Disengage the clamps and guides to remove the antenna cord sub-assembly.



b.

for Integrated Type:

i.

Disengage the claws.

E451696C01
2.719,2.354 2.146,1.938 2.146,1.938 2.823,1.948 true 4.104,2.458 4.708,2.198 4.708,2.198 4.677,2.615 true 5.563,3.323 6,2.854 true 5.375,2.552 5.771,2.333 true 5.406,3.292 5.615,3.448 0.208,0.156 10 false *b 1.875,1.833 2.094,2 0.219,0.167 10 true *a 4.74,2.083 4.958,2.25 0.219,0.167 10 true *a 5.823,2.219 6.042,2.385 0.219,0.167 10 true *a
*a Clamp *b Guide



ii.

Disconnect the connector.


iii.

Disengage the clamps and guide to remove the antenna cord sub-assembly.



Hide 63310 5.REMOVE ROOF HEADLINING (for 5 Door)

Hide 63310 6.REMOVE ROOF HEADLINING (for 3 Door)

Hide 86101J 7.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for 5 Door Normal Roof)

a.

for TMC Made:

i.

Remove each adhesive tape from the roof headlining.

E436750C01
0,0 0,0 false
V100155

Adhesive Tape - -



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



b.

for TMMF, TMMCZ Made:

i.

Remove each adhesive tape from the roof headlining.

E454952C01
0,0 0,0 false
V100155

Adhesive Tape - -



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



Hide 86101J 8.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for 3 Door Normal Roof)

a.

Remove each adhesive tape from the roof headlining.

E454943C01
0,0 0,0 false
V100155

Adhesive Tape - -



b.

Remove the No. 2 antenna cord sub-assembly by peeling the No. 2 antenna cord sub-assembly away from the butyl tape.


Hide 86101J 9.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for Panoramic Moon Roof)

a.

Remove each adhesive tape from the roof headlining.

E451699


b.

Remove the No. 2 antenna cord sub-assembly by peeling the No. 2 antenna cord sub-assembly away from the butyl tape.


Hide 10.REMOVE NO. 8 ANTENNA CORD SUB-ASSEMBLY (for 3 Door Normal Roof)

a.
E453813

Disconnect the connector.


b.

Remove the bolt.


c.

Disengage the guide to remove the No. 8 antenna cord sub-assembly.


Hide 67751 11.REMOVE BACK DOOR TRIM BOARD (for 5 Door)

Hide 67761A 12.REMOVE BACK DOOR TRIM COVER (for 5 Door)

Hide 86101R 13.REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY (for 5 Door)

a.
E439177C01
1.75,0.333 2.083,0.333 true 1.458,1.417 1.792,1.417 true 1.208,1.333 1.427,1.552 0.219,0.219 10 true *b 1.5,0.229 1.719,0.448 0.219,0.219 10 true *a
*a Clamp
*b Guide


Disconnect the 2 connectors.


b.

Disengage the clamp.


c.

Remove the bolt.


d.

Disengage the guide to remove the No. 5 antenna cord sub-assembly.


Hide 86101V 14.REMOVE NO. 6 ANTENNA CORD SUB-ASSEMBLY (for 5 Door)

a.
E439178

Disconnect the 2 connectors.


b.

Disengage the clamps to remove the No. 6 antenna cord sub-assembly.


Hide 15.REMOVE NO. 7 ANTENNA CORD SUB-ASSEMBLY (for 5 Door)

a.
E439179

Disconnect the 2 connectors.


b.

Disengage the clamps to remove the No. 7 antenna cord sub-assembly.


Hide 86101Q 16.REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY (for 5 Door)

a.
E436751

Disengage the clamp.


b.
E436752

Disengage the claws to separate the grommet.


c.
E436753C01
0,0 0,0 false
V100155

Protective Tape


Install the protective tape as shown in the illustration.


d.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the grommet.


e.
E436754C01
1.5,1.417 1.5,1.083 true 2.271,2.635 2.521,2.635 true 1.438,0.885 1.667,1.083 0.229,0.198 10 true *a 2.552,2.542 2.781,2.74 0.229,0.198 10 false *b
*a Nonwoven Tape
*b Rope


Secure a rope to the No. 4 antenna cord sub-assembly with nonwoven tape as shown in the illustration.

NOTICE:
·

As conduction performance may degrade if adhesive from the nonwoven tape contacts the connecting parts of the connector, cover the connector with a plastic bag or similar before applying the nonwoven tape.

·

Make sure that the rope is secured with nonwoven tape to prevent the rope from separating from the No. 4 antenna cord sub-assembly when removing it.




f.
E436755C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 4 antenna cord sub-assembly as shown in the illustration.

NOTICE:
·

The rope will be used when installing the No. 4 antenna cord sub-assembly. Leave the rope inside the back door panel sub-assembly.

·

This step should not be performed with the back door panel sub-assembly removed from the vehicle.