Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.11
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Telephone transceiver assembly (w/ Telephone Transceiver Assembly)

·

Harness or connector



WIRING DIAGRAM

for TMC Made without Telephone Transceiver Assembly
E402556E30
1.583,0.958 2.042,1.188 0.458,0.229 10 false SNS2 2.052,0.823 2.271,1.01 0.219,0.188 10 false 1 5.448,0.823 5.667,1.01 0.219,0.188 10 false 25 5.771,0.958 6.49,1.25 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.448,1.823 5.729,2.063 0.281,0.24 10 false 22 5.781,1.969 6.24,2.198 0.458,0.229 10 false MIN- 5.74,2.469 6.198,2.698 0.458,0.229 10 false H80 5.74,2.635 6.927,3.031 1.188,0.396 10 false Radio and Display Receiver Assembly 0.917,3.073 1.375,3.302 0.458,0.229 10 false V7 1.063,2.396 2.49,2.885 1.427,0.49 10 false Telephone Microphone Assembly 0.927,3.229 2.885,3.583 1.958,0.354 10 false Map Light Assembly 2.573,1.854 3.031,2.083 0.458,0.229 10 false MCO- 1.604,1.938 2.063,2.167 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.104,0.833 3.563,1.063 0.458,0.229 10 false 13 3.115,1.844 3.573,2.073 0.458,0.229 10 false 14 1.063,2.208 1.521,2.438 0.458,0.229 10 false MC

for TMC Made with Telephone Transceiver Assembly
E445949E08
1.594,0.917 2.208,1.115 0.615,0.198 10 false SNS2 1.656,1.917 2.271,2.115 0.615,0.198 10 false MIC- 2.604,0.813 3.219,1.01 0.615,0.198 10 false SNS2 2.594,1.823 3.208,2.021 0.615,0.198 10 false MCO- 3.063,0.802 3.677,1 0.615,0.198 10 false 13 3.094,1.823 3.708,2.021 0.615,0.198 10 false 14 1.021,2.208 1.635,2.406 0.615,0.198 10 false MC 1.021,2.365 2.427,2.802 1.406,0.438 10 false Telephone Microphone Assembly 0.927,3.042 1.542,3.24 0.615,0.198 10 false V7 0.927,3.198 2.688,3.51 1.76,0.313 10 false Map Light Assembly 3.688,1.823 4.302,2.021 0.615,0.198 10 false 7 5.5,0.813 6.115,1.01 0.615,0.198 10 false 25 3.854,1.927 4.469,2.125 0.615,0.198 10 false MCI- 5.76,0.917 6.375,1.115 0.615,0.198 10 false SNS2 3.573,2.469 4.188,2.667 0.615,0.198 10 false H85 3.573,2.625 4.969,3 1.396,0.375 10 false Telephone Transceiver Assembly 5.583,2.448 6.198,2.646 0.615,0.198 10 false H80 5.583,2.604 6.781,2.99 1.198,0.385 10 false Radio and Display Receiver Assembly 2.042,0.844 2.198,1.042 0.156,0.198 10 false 1 2.073,1.844 2.229,2.042 0.156,0.198 10 false 2

except TMC Made without Telephone Transceiver Assembly
E402556E40
1.583,0.917 2.042,1.146 0.458,0.229 10 false SNS2 2.052,0.833 2.271,1.021 0.219,0.188 10 false 1 5.5,0.823 5.719,1.01 0.219,0.188 10 false 25 5.75,0.927 6.469,1.219 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.5,1.833 5.781,2.073 0.281,0.24 10 false 22 5.76,1.938 6.219,2.167 0.458,0.229 10 false MIN- 5.604,2.448 6.063,2.677 0.458,0.229 10 false H80 5.604,2.604 6.792,3 1.188,0.396 10 false Radio and Display Receiver Assembly 0.917,3.063 1.375,3.292 0.458,0.229 10 false V6 1.063,2.396 2.49,2.885 1.427,0.49 10 false Telephone Microphone Assembly 0.927,3.229 2.885,3.583 1.958,0.354 10 false Map Light Assembly 2.604,1.833 3.063,2.063 0.458,0.229 10 false MCO- 1.656,1.917 2.115,2.146 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.094,0.823 3.552,1.052 0.458,0.229 10 false 15 3.115,1.813 3.573,2.042 0.458,0.229 10 false 4 1.063,2.208 1.521,2.438 0.458,0.229 10 false MC

except TMC Made with Telephone Transceiver Assembly
E445949E03
1.594,0.917 2.208,1.115 0.615,0.198 10 false SNS2 1.656,1.917 2.271,2.115 0.615,0.198 10 false MIC- 2.604,0.813 3.219,1.01 0.615,0.198 10 false SNS2 2.594,1.823 3.208,2.021 0.615,0.198 10 false MCO- 3.063,0.802 3.677,1 0.615,0.198 10 false 15 3.083,1.823 3.698,2.021 0.615,0.198 10 false 4 1.021,2.208 1.635,2.406 0.615,0.198 10 false MC 1.021,2.365 2.427,2.802 1.406,0.438 10 false Telephone Microphone Assembly 0.927,3.042 1.542,3.24 0.615,0.198 10 false V6 0.927,3.198 2.688,3.51 1.76,0.313 10 false Map Light Assembly 3.688,1.823 4.302,2.021 0.615,0.198 10 false 7 5.5,0.813 6.115,1.01 0.615,0.198 10 false 25 3.854,1.927 4.469,2.125 0.615,0.198 10 false MCI- 5.76,0.917 6.375,1.115 0.615,0.198 10 false SNS2 3.573,2.469 4.188,2.667 0.615,0.198 10 false H85 3.573,2.625 5,3 1.427,0.375 10 false Telephone Transceiver Assembly 5.583,2.448 6.198,2.646 0.615,0.198 10 false H80 5.583,2.604 6.781,2.99 1.198,0.385 10 false Radio and Display Receiver Assembly 2.042,0.844 2.198,1.042 0.156,0.198 10 false 1 2.073,1.844 2.229,2.042 0.156,0.198 10 false 2

PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for TMC Made without Telephone Transceiver Assembly A
for TMC Made with Telephone Transceiver Assembly B
except TMC Made without Telephone Transceiver Assembly C
except TMC Made with Telephone Transceiver Assembly D



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

C

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

D

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V7-13 (SNS2) Always Below 1 Ω
H80-22 (MIN-) - V7-14 (MCO-) Always Below 1 Ω
H80-25 (SNS2) or V7-13 (SNS2) - Body ground Always 10 kΩ or higher
H80-22 (MIN-) or V7-14 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the MC telephone microphone assembly connector.


c.
E438880C01
1.396,0.115 1.969,0.438 0.573,0.323 0.917,1.854 1.208,1.417 true 1.698,1.885 1.438,1.406 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.656,1.917 1.167,2.125 0.51,0.208 10 false MCO- 1.656,1.917 2.188,2.177 0.531,0.26 10 false SNS2 1.594,0.219 2.104,0.427 0.51,0.208 10 false V7
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-13 (SNS2) - V7-14 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.INSPECT MAP LIGHT ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the MC telephone microphone assembly connector.


c.
E437721C01
1.573,0.396 1.958,0.646 0.385,0.25 1.458,2.813 1.854,3.063 0.396,0.25 0.865,2.125 1.167,1.625 true 1.646,2.125 1.375,1.615 true 1.104,3.781 1.396,3.417 true 1.844,3.927 1.573,3.417 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 0.583,2.146 1.083,2.365 0.5,0.219 10 false MCO- 1.635,2.146 2.115,2.354 0.479,0.208 10 false SNS2 1.563,2.865 2.073,3.063 0.51,0.198 10 false MC 1.677,0.448 2.156,0.656 0.479,0.208 10 false V7 1.823,3.948 2.323,4.167 0.5,0.219 10 false MIC- 0.938,3.844 1.438,4.063 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-13 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V7-14 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V7-13 (SNS2) - Body ground Always 10 kΩ or higher
V7-14 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V7-13 (SNS2) Always Below 1 Ω
H80-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Disconnect the V7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-7 (MCI-) - V7-14 (MCO-) Always Below 1 Ω
H85-7 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (MCI-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (MCI-)
a.
E427272C19
1.51,0.531 2.01,0.781 0.5,0.25 2.25,1.688 2.604,1.073 true 1.635,0.552 2,0.833 0.365,0.281 10 false H85 2.656,0.958 3.115,1.156 0.458,0.198 10 false MCI- 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

8.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E438880C01
1.396,0.115 1.969,0.438 0.573,0.323 0.917,1.854 1.208,1.417 true 1.698,1.885 1.438,1.406 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.656,1.917 1.167,2.125 0.51,0.208 10 false MCO- 1.656,1.917 2.188,2.177 0.531,0.26 10 false SNS2 1.594,0.219 2.104,0.427 0.51,0.208 10 false V7
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-13 (SNS2) - V7-14 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

9.INSPECT MAP LIGHT ASSEMBLY
9.INSPECT MAP LIGHT ASSEMBLY
a.
E437721C01
1.573,0.396 1.958,0.646 0.385,0.25 1.458,2.813 1.854,3.063 0.396,0.25 0.865,2.125 1.167,1.625 true 1.646,2.125 1.375,1.615 true 1.104,3.781 1.396,3.417 true 1.844,3.927 1.573,3.417 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 0.583,2.146 1.083,2.365 0.5,0.219 10 false MCO- 1.635,2.146 2.115,2.354 0.479,0.208 10 false SNS2 1.563,2.865 2.073,3.063 0.51,0.198 10 false MC 1.677,0.448 2.156,0.656 0.479,0.208 10 false V7 1.823,3.948 2.323,4.167 0.5,0.219 10 false MIC- 0.938,3.844 1.438,4.063 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-13 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V7-14 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V7-13 (SNS2) - Body ground Always 10 kΩ or higher
V7-14 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V6 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V6-15 (SNS2) Always Below 1 Ω
H80-22 (MIN-) - V6-4 (MCO-) Always Below 1 Ω
H80-25 (SNS2) or V6-15 (SNS2) - Body ground Always 10 kΩ or higher
H80-22 (MIN-) or V6-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the MC telephone microphone assembly connector.


c.
E265420C21
1.396,0.115 1.969,0.438 0.573,0.323 1.073,1.719 1.365,1.281 true 2.135,1.688 1.781,1.135 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 2.104,1.719 2.615,1.927 0.51,0.208 10 false MCO- 0.813,1.729 1.344,1.99 0.531,0.26 10 false SNS2 1.594,0.156 2.104,0.365 0.51,0.208 10 false V6
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-15 (SNS2) - V6-4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

12.INSPECT MAP LIGHT ASSEMBLY
12.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the MC telephone microphone assembly connector.


c.
E445954C01
1.469,0.417 1.969,0.667 0.5,0.25 1.448,2.823 1.948,3.073 0.5,0.25 1.125,2.156 1.427,1.656 true 2.01,2.063 1.74,1.552 true 1.104,3.781 1.396,3.417 true 1.906,3.781 1.594,3.417 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 1.958,2.104 2.458,2.323 0.5,0.219 10 false MCO- 0.823,2.177 1.302,2.385 0.479,0.208 10 false SNS2 1.594,2.844 2.104,3.042 0.51,0.198 10 false MC 1.635,0.438 2.115,0.646 0.479,0.208 10 false V6 1.896,3.802 2.396,4.021 0.5,0.219 10 false MIC- 0.802,3.813 1.302,4.031 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-15 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V6-4 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V6-15 (SNS2) - Body ground Always 10 kΩ or higher
V6-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V6 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V6-15 (SNS2) Always Below 1 Ω
H80-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Disconnect the V6 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-7 (MCI-) - V6-4 (MCO-) Always Below 1 Ω
H85-7 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (MCI-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (MCI-)
a.
E427272C19
1.51,0.531 2.01,0.781 0.5,0.25 2.25,1.688 2.604,1.073 true 1.635,0.552 2,0.833 0.365,0.281 10 false H85 2.656,0.958 3.115,1.156 0.458,0.198 10 false MCI- 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

16.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E265420C20
1.469,0.25 1.969,0.5 0.5,0.25 2.229,1.677 1.781,1.146 true 1.042,1.667 1.354,1.292 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 2.219,1.698 2.729,1.906 0.51,0.208 10 false MCO- 0.698,1.677 1.229,1.938 0.531,0.26 10 false SNS2 1.635,0.271 1.948,0.469 0.313,0.198 10 false V6
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-15 (SNS2) - V6-4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

17.INSPECT MAP LIGHT ASSEMBLY
17.INSPECT MAP LIGHT ASSEMBLY
a.
E445954C01
1.469,0.417 1.969,0.667 0.5,0.25 1.448,2.823 1.948,3.073 0.5,0.25 1.125,2.156 1.427,1.656 true 2.01,2.063 1.74,1.552 true 1.104,3.781 1.396,3.417 true 1.906,3.781 1.594,3.417 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 1.958,2.104 2.458,2.323 0.5,0.219 10 false MCO- 0.823,2.177 1.302,2.385 0.479,0.208 10 false SNS2 1.594,2.844 2.104,3.042 0.51,0.198 10 false MC 1.635,0.438 2.115,0.646 0.479,0.208 10 false V6 1.896,3.802 2.396,4.021 0.5,0.219 10 false MIC- 0.802,3.813 1.302,4.031 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-15 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V6-4 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V6-15 (SNS2) - Body ground Always 10 kΩ or higher
V6-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY