Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › from 2021.11
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421991 TRANSMISSION CONTROL CABLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before adjusting the transmission control cable assembly, check that the shift lever position sensor and shift lever are in N.


a.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Engage the guide to connect the transmission control cable assembly to vehicle body.


c.

Install the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


d.

Install the transmission control cable assembly to the hybrid vehicle transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


e.

Engage the clamp to connect the transmission control cable assembly.


f.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


g.
C377951N01
2.833,1.385 2.99,1.583 0.156,0.198 10 false N 2.583,2 2.75,2.177 0.167,0.177 10 false P

Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.


h.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


i.
C400603C07
1.854,1.74 1.531,1.198 false 2.583,1.677 2.167,0.979 false 2.615,1.698 2.927,1.854 0.313,0.156 10 false *1 1.875,1.771 2.188,1.927 0.313,0.156 10 false *2
*1 Adjuster Case
*2 Adjuster Case Cover


Slide the adjuster case cover in the direction shown by the arrow.


j.
C400817C06
2.156,1.635 1.896,1.177 false 2.646,1.594 2.313,1.031 false 2.635,1.583 2.948,1.74 0.313,0.156 10 false *1 2.156,1.646 2.469,1.802 0.313,0.156 10 false *2
*1 Adjuster Case
*2 Lock Piece


Using a precision screwdriver, pull out the lock piece of the adjuster case.


k.
C400818C03
0.448,1.208 0.625,1.208 0.625,1.208 1.729,1.49 true 2.188,1.26 2.896,2.208 2.896,2.208 2.208,3.479 true 0.26,1.115 0.573,1.271 0.313,0.156 10 false *1 2.01,0.365 2.323,0.521 0.313,0.156 10 false *a 2.948,2.104 3.26,2.26 0.313,0.156 10 false *2
*1 Lock Nut
*2 Stopper
*a Push in


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


l.
C435107C01
0.771,1.104 0.531,0.979 false 2.604,1.021 2.365,0.896 false 0.344,0.896 0.656,1.052 0.313,0.156 10 false *1 2.208,0.813 2.521,0.969 0.313,0.156 10 false *1
*1 Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

After installation, check that the outer part of the stopper is as shown in the illustration.

·

Do not forcibly pull the transmission control cable assembly into the cabin.




m.
C435108

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.

·

Before connecting the floor shift transmission control select cable, check that the shift lever is in N.




n.
C435105C01
1.854,0.656 2.25,0.99 true 2.75,1.323 2.531,1.052 true 1.646,0.563 1.844,0.75 0.198,0.188 10 true *2 2.688,1.354 2.917,1.542 0.229,0.188 10 true *1
*1 Lock Piece
*2 Adjuster Case


Push in the lock piece of the adjuster case to lock it.

NOTICE:
C414647C05
1.271,0.333 1.604,0.333 false 2.333,1.667 2.583,1.167 2.583,1.167 2.75,1.167 true 2.781,1.063 3.094,1.219 0.313,0.156 10 false *1 1.646,0.24 1.958,0.396 0.313,0.156 10 false *2
*1 Transmission Control Cable Assembly
*2 Lever Shaft


·

When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

·

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.




o.
C435106C01
2.844,1.302 2.573,1.052 true 2.354,1.396 2.354,1.094 true 2.771,1.323 3.021,1.49 0.25,0.167 10 true *1 2.281,1.427 2.531,1.594 0.25,0.167 10 true *2
*1 Adjuster Case
*2 Adjuster Case Cover


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.



Hide 58910C 2.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 58153 3.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR (for TMMF, TMMCZ Made)

a.

Install the front No. 2 floor heat insulator to the vehicle body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58153 4.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR (for TMC Made)

a.

Install the front No. 2 floor heat insulator to the vehicle body with the 4 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58151 5.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57543C 7.INSTALL CENTER NO. 1 FLOOR BRACE (for TMMF, TMMCZ Made)

Hide 51447D 8.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMMF, TMMCZ Made)

Hide 51447D 9.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

Hide 58166A 10.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 11.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 51451A 12.INSTALL CENTER ENGINE UNDER COVER (w/ Cover)

Hide G9200 13.INSTALL INVERTER WITH CONVERTER ASSEMBLY