Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494155 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made)  C138049  Stop Lamp Relay Internal Electronic Failure  


DESCRIPTION

When the skid control ECU (brake actuator assembly) applies the brakes after receiving a brake request signal from the trailer sway control, the skid control ECU (brake actuator assembly) operates the stop light switch assembly to illuminate the stop lights.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C138049 Stop Lamp Relay Internal Electronic Failure STPO terminal voltage is 1.4 to 2.2 V and stop light relay is OFF for 2.5 seconds or more.
·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

b.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Post-procedure1

c.

Turn the ignition switch off.


Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-12 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A37-12 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-28 (STPO) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


Procedure1

b.

Perform the Active Test of the "Stop Lamp Relay" using the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Lamp Relay Stop light switch assembly (STOP terminal output) OFF/ON Check that the stop light switch assembly (STPO terminal output) turns ON when the brake pedal is released, the stop lights illuminate, and the "Stop Lamp Relay" and "STPO" Data List items switch to ON.
Chassis > Brake > Active Test
Tester Display
Stop Lamp Relay
50004 435 27

c.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop light turns ON/OFF in response to the GTS operation



Post-procedure1

d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

7.INSPECT STOP LIGHT SWITCH ASSEMBLY
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Pre-procedure1

d.

Turn the ignition switch off.


Result:
Result Proceed to
C138049 is output A
C138049 is not output B



A

B

7.INSPECT STOP LIGHT SWITCH ASSEMBLY

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-4 (ACC) - Body ground Always 11 to 14 V


Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT STOP LIGHT SWITCH ASSEMBLY

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY (VSC ACC)

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-4 (ACC) - Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR