Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494155 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made)  C13807F  Stop Lamp Relay Actuator Stuck Off  


DESCRIPTION

Refer to DTC C13807E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made)>C13807E

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C13807F Stop Lamp Relay Actuator Stuck Off ACC terminal is ON and STP2 terminal is OFF for 2 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light assembly


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made)>UTILITY



HINT:

When DTC P057111 and/or P057112 are output together with DTC C13807F, inspect and repair the trouble areas indicated by DTC P057111 and/or P057112 first.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Perform the stop light control relay (stop light switch assembly) Active Test, and confirm that the stop lights illuminate and turn off and the value of "Stop Light SW", "Stop Light Relay" and "STPO" changes.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
Stop Lamp Relay Stop light control relay (stop light switch assembly) OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds


With the brake pedal released, check that the stop lights illuminate and value of "Stop Light Relay" on the GTS changes to ON when "Stop Lamp Relay" is ON
Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Stop Light Relay Stop light control relay (stop light switch assembly) status
(STP terminal input)
OFF / ON OFF: Stop light control relay (stop light switch assembly) off and brake pedal released
ON: Stop light control relay (stop light switch assembly) on or brake pedal depressed
HINT:

The voltage of power supplied to the stop lights is measured at the STP terminal.


STPO Stop light control relay (stop light switch assembly) status
(STPO terminal output)
OFF / ON OFF: Stop light control relay (stop light switch assembly) off (Stop light off)
ON: Stop light control relay (stop light switch assembly) on (Stop light on)
HINT:

When STPO is ON, the stop light control relay (stop light switch assembly) turns ON and the stop lights illuminate


Chassis > Brake > Active Test
Active Test Display
Stop Lamp Relay
Data List Display
Stop Light SW
Stop Light Relay
STPO
50004 435 27 59,67,252

b.

Turn the ignition switch off.


Result:
Data List Status Stop Light Illumination Status Proceed to
Stop Light SW Stop Light Relay STPO
OFF OFF ON Not illuminated A
OFF OFF ON Illuminated B
ON ON ON Illuminated C



A

2.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

B

7.CHECK BRAKE ACTUATOR ASSEMBLY

C

8.CHECK BRAKE ACTUATOR ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-28 (STPO) - Body ground Always 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CHECK BRAKE ACTUATOR ASSEMBLY

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
3.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK FOR SHORT TO GROUND IN STP CIRCUIT
4.CHECK FOR SHORT TO GROUND IN STP CIRCUIT
a.

Check that there is no short to ground in the STP circuit (wire harnesses, connectors and stop lights).

OK:

There is no short to ground.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE MALFUNCTIONING PART

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-1 (OUT) - A37-12 (STP2) Always Below 1 Ω



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK STOP LIGHT SWITCH ASSEMBLY

Pre-procedure1

a.
C401043C89
0.448,0.448 0.781,0.698 0.333,0.25 2.26,1.781 1.854,1.052 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.49 0.958,0.688 0.458,0.198 10 false A63 2.323,1.708 2.781,1.906 0.458,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-4 (ACC) - Body ground Always 11 to 14 V



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK BRAKE ACTUATOR ASSEMBLY

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK BRAKE ACTUATOR ASSEMBLY

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-12 (STP2) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

9.CHECK STOP LIGHT SWITCH ASSEMBLY
9.CHECK STOP LIGHT SWITCH ASSEMBLY

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-12 (STP2) - Body ground Always Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

10.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
10.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
a.

Check that there is no short to +B in the STP2 circuit (wire harnesses, connectors and ECUs).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART