Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model) › from 2021.11
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424996 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

ECM


Radar Cruise1

WIRING DIAGRAM

for M15A-FKS


C441854E06
0.094,0.406 1.396,1.021 1.302,0.615 10 false for STRG LOCK Fuse*1, AM1 Fuse*2 0.438,1.073 2.052,1.521 1.615,0.448 10 false from IGP Relay 2.385,0.75 4.375,0.948 1.99,0.198 10 false STOP 2.115,1.24 4.104,1.438 1.99,0.198 10 false ECU-IGP NO. 3 3.167,2.083 5.156,2.281 1.99,0.198 10 false Stop Light Switch Assembly 3.177,1.938 3.938,2.115 0.76,0.177 10 false A63 3.563,0.594 3.719,0.792 0.156,0.198 10 false B 3.573,1.094 3.729,1.292 0.156,0.198 10 false B 3.552,1.615 4.01,1.813 0.458,0.198 10 false GND 4.156,0.49 4.313,0.688 0.156,0.198 10 false L 4.167,1.281 4.323,1.479 0.156,0.198 10 false L 3.396,0.49 4.063,0.729 0.667,0.24 10 false 7 3.396,0.99 4.26,1.281 0.865,0.292 10 false 6 3.396,1.479 3.99,1.74 0.594,0.26 10 false 2 4.344,0.354 4.948,0.583 0.604,0.229 10 false 3 4.344,1.156 4.948,1.365 0.604,0.208 10 false 5 5.781,0.365 6.24,0.563 0.458,0.198 10 false STP 5.781,1.156 6.24,1.354 0.458,0.198 10 false ST1- 5.531,0.375 6.323,0.604 0.792,0.229 10 false 21 5.521,1.156 6.396,1.385 0.875,0.229 10 false 22 6.208,2.115 6.646,2.365 0.438,0.25 10 false ECM 6.24,1.948 7.156,2.167 0.917,0.219 10 false A54 5.406,2.969 7.156,3.49 1.75,0.521 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly) 5.354,2.583 5.729,2.76 0.375,0.177 10 false H20 3.573,2.563 4.031,2.76 0.458,0.198 10 false STP2 5.417,2.427 5.781,2.833 0.365,0.406 10 false 4 4.104,2.396 4.313,2.604 0.208,0.208 10 false 5 2.844,2.958 4.698,3.333 1.854,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 6.01,2.583 6.552,2.771 0.542,0.188 10 false STP 4.344,2.583 4.698,2.771 0.354,0.188 10 false A37 3.135,4.292 3.865,4.594 0.729,0.302 10 false TCM*3 3.156,4.125 5.146,4.323 1.99,0.198 10 false D71 4.01,3.646 4.552,3.833 0.542,0.188 10 false 43 3.635,3.76 4.094,3.958 0.458,0.198 10 false STP 6.01,3.76 6.469,3.958 0.458,0.198 10 false STP1 5.781,3.656 5.99,3.865 0.208,0.208 10 false 21 5.333,4.177 7.156,4.698 1.823,0.521 10 false Certification ECU (Smart Key ECU Assembly)*1 5.344,4.01 5.76,4.219 0.417,0.208 10 false H45 5.771,2.417 6.135,2.823 0.365,0.406 10 false 8 5.688,2.583 6.063,2.76 0.375,0.177 10 false H19 0.083,3.01 2.917,3.625 2.833,0.615 10 false *1: w/ Entry and Start System 0.083,3.344 3.125,3.667 3.042,0.323 10 false *2: w/o Entry and Start System 0.094,3.729 2.948,4.167 2.854,0.438 10 false *3: for CVT 5.385,2.76 5.76,2.938 0.375,0.177 10 false *1 5.74,2.76 6.115,2.938 0.375,0.177 10 false *2 4.031,2.583 4.385,2.771 0.354,0.188 10 false A36 4.396,2.385 4.719,2.583 0.323,0.198 10 false 12 4.073,2.771 4.448,2.948 0.375,0.177 10 false *4 4.354,2.771 4.729,2.948 0.375,0.177 10 false *5 0.083,4.083 2.938,4.521 2.854,0.438 10 false *4: for TMC Made 0.083,4.417 2.833,4.708 2.75,0.292 10 false *5: for TMMF Made


for 1KR-FE


C441855E08
0.125,0.292 1.448,0.958 1.323,0.667 10 false for STRG LOCK Fuse*1, AM1 Fuse*2 0.438,1.073 2.052,1.521 1.615,0.448 10 false from IGP Relay 2.385,0.75 4.375,0.948 1.99,0.198 10 false STOP 2.115,1.24 4.104,1.438 1.99,0.198 10 false ECU-IGP NO. 3 3.167,2.083 5.156,2.281 1.99,0.198 10 false Stop Light Switch Assembly 3.177,1.938 3.938,2.115 0.76,0.177 10 false A63 3.563,0.594 3.719,0.792 0.156,0.198 10 false B 3.573,1.094 3.729,1.292 0.156,0.198 10 false B 3.552,1.615 4.01,1.813 0.458,0.198 10 false GND 4.156,0.49 4.313,0.688 0.156,0.198 10 false L 4.167,1.281 4.323,1.479 0.156,0.198 10 false L 3.396,0.49 4.063,0.729 0.667,0.24 10 false 7 3.396,0.99 4.26,1.281 0.865,0.292 10 false 6 3.396,1.479 3.99,1.74 0.594,0.26 10 false 2 4.344,0.354 4.948,0.583 0.604,0.229 10 false 3 4.344,1.156 4.948,1.365 0.604,0.208 10 false 5 5.781,0.365 6.24,0.563 0.458,0.198 10 false STP 5.781,1.156 6.24,1.354 0.458,0.198 10 false ST1- 5.531,0.375 6.323,0.604 0.792,0.229 10 false 57 5.521,1.156 6.396,1.385 0.875,0.229 10 false 24 6.208,2.115 6.646,2.365 0.438,0.25 10 false ECM 6.24,1.948 7.156,2.167 0.917,0.219 10 false A55 6.01,3 6.469,3.198 0.458,0.198 10 false STP 5.823,2.906 6.073,3.104 0.25,0.198 10 false 2 5.552,3.563 7.156,4.042 1.604,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.531,3.385 6.49,3.583 0.958,0.198 10 false A37 0.438,3.771 2.667,4.01 2.229,0.24 10 false *1: w/ Entry and Start System 0.417,4.24 2.646,4.479 2.229,0.24 10 false *2: w/o Entry and Start System


for G16E-GTS


C441855E09
0.115,0.365 1.427,0.896 1.313,0.531 10 false for STRG LOCK Fuse*1, AM1 Fuse*2 0.438,1.073 2.052,1.521 1.615,0.448 10 false from IGP Relay 2.385,0.75 4.375,0.948 1.99,0.198 10 false STOP 2.115,1.24 4.104,1.438 1.99,0.198 10 false ECU-IGP NO. 3 3.167,2.083 5.156,2.281 1.99,0.198 10 false Stop Light Switch Assembly 3.177,1.938 3.938,2.115 0.76,0.177 10 false A63 3.563,0.594 3.719,0.792 0.156,0.198 10 false B 3.573,1.094 3.729,1.292 0.156,0.198 10 false B 3.552,1.615 4.01,1.813 0.458,0.198 10 false GND 4.156,0.49 4.313,0.688 0.156,0.198 10 false L 4.167,1.281 4.323,1.479 0.156,0.198 10 false L 3.396,0.49 4.063,0.729 0.667,0.24 10 false 7 3.396,0.99 4.26,1.281 0.865,0.292 10 false 6 3.396,1.479 3.99,1.74 0.594,0.26 10 false 2 4.344,0.354 4.948,0.583 0.604,0.229 10 false 3 4.344,1.156 4.948,1.365 0.604,0.208 10 false 5 5.781,0.365 6.24,0.563 0.458,0.198 10 false STP 5.781,1.156 6.24,1.354 0.458,0.198 10 false ST1- 5.531,0.354 6.323,0.583 0.792,0.229 10 false 21 5.521,1.135 6.396,1.365 0.875,0.229 10 false 22 6.208,2.115 6.646,2.365 0.438,0.25 10 false ECM 6.188,1.948 7.104,2.167 0.917,0.219 10 false A106 6.01,3 6.469,3.198 0.458,0.198 10 false STP2 5.823,2.885 6.073,3.083 0.25,0.198 10 false 5 5.552,3.563 7.156,4.042 1.604,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.531,3.385 6.49,3.583 0.958,0.198 10 false A108 0.406,3.396 2.76,3.844 2.354,0.448 10 false *1: w/ Entry and Start System 0.417,3.969 2.771,4.417 2.354,0.448 10 false *2: w/o Entry and Start System


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



c.

Connect the A63 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7 (B) - Body ground Always 11 to 14 V
A63-6 (B) - Body ground Ignition switch ON 11 to 14 V
A63-6 (B) - Body ground Ignition switch off Below 1 V



c.

Connect the A63 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

4.CONFIRM MODEL

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B
for G16E-GTS C



A

5.CONFIRM MODEL

B

8.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

6.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A54 ECM connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*

*: w/ Entry and Start System



e.

Disconnect the F19*1 or F20*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

Disconnect the D71 TCM connector.*

*: for CVT



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-22 (ST1-) - A63-5 (L) Always Below 1 Ω
A54-21 (STP) - A63-3 (L) Always Below 1 Ω
A54-22 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A54-21 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



h.

Connect the D71 TCM connector.*

*: for CVT



i.

Connect the F19*1 or F20*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



j.

Connect the H45 certification ECU (smart key ECU assembly) connector.*

*: w/ Entry and Start System



k.

Connect the A36 skid control ECU (brake actuator assembly) connector.


l.

Connect the A63 stop light switch assembly connector.


m.

Connect the A54 ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A54 ECM connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*

*: w/ Entry and Start System



e.

Disconnect the F19*1 or F20*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

Disconnect the D71 TCM connector.*

*: for CVT



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-22 (ST1-) - A63-5 (L) Always Below 1 Ω
A54-21 (STP) - A63-3 (L) Always Below 1 Ω
A54-22 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A54-21 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



h.

Connect the D71 TCM connector.*

*: for CVT



i.

Connect the F19*1 or F20*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



j.

Connect the H45 certification ECU (smart key ECU assembly) connector.*

*: w/ Entry and Start System



k.

Connect the A37 skid control ECU (brake actuator assembly) connector.


l.

Connect the A63 stop light switch assembly connector.


m.

Connect the A54 ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A55 ECM connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-24 (ST1-) - A63-5 (L) Always Below 1 Ω
A55-57 (STP) - A63-3 (L) Always Below 1 Ω
A55-24 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A55-57 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



d.

Connect the A63 stop light switch assembly connector.


e.

Connect the A55 ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A106 ECM connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A106-22 (ST1-) - A63-5 (L) Always Below 1 Ω
A106-21 (STP) - A63-3 (L) Always Below 1 Ω
A106-22 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A106-21 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



d.

Connect the A63 stop light switch assembly connector.


e.

Connect the A106 ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR