Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › from 2021.11
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0425249 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 9 global CAN junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH (A)

·

Power source circuit of blind spot monitor sensor RH (A)

·

Blind spot monitor sensor RH (A) ground circuit

·

Blind spot monitor sensor LH (B)


U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (B)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 9 global CAN junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH (B)

·

Power source circuit of blind spot monitor sensor LH (B)

·

Blind spot monitor sensor LH (B) ground circuit

·

Blind spot monitor sensor RH (A)



WIRING DIAGRAM

E386359E37
2.375,2.5 3.542,3.021 1.167,0.521 10 false Blind Spot Monitor Sensor LH (B) 5.542,2.458 6.708,3.052 1.167,0.594 10 false Blind Spot Monitor Sensor RH (A) 2.375,2.354 3.625,2.594 1.25,0.24 10 false T6*1, O38*2 5.552,2.313 6.885,2.5 1.333,0.188 10 false S6*1, O37*2 2.5,1.01 2.927,1.208 0.427,0.198 10 false 5 2.417,1.719 2.656,1.885 0.24,0.167 10 false 10 6.719,1.75 6.917,1.906 0.198,0.156 10 false 10 6.74,1.01 6.896,1.156 0.156,0.146 10 false 5 4.063,0.833 4.49,1.031 0.427,0.198 10 false 11 4.042,1.458 4.469,1.656 0.427,0.198 10 false 22 5.51,0.844 5.729,1.01 0.219,0.167 10 false 1 5.521,1.469 5.688,1.646 0.167,0.177 10 false 6 4.063,3.823 4.49,4.021 0.427,0.198 10 false 20 5.115,0.844 5.292,1.01 0.177,0.167 10 false 10 5.698,0.833 6.125,1.031 0.427,0.198 10 false CA2P 3.271,0.844 3.656,1.021 0.385,0.177 10 false CA2P 3.26,1.479 3.688,1.677 0.427,0.198 10 false CA2N 5.698,1.469 6.125,1.667 0.427,0.198 10 false CA2N 4.135,3.458 4.563,3.656 0.427,0.198 10 false 9 5.094,1.469 5.354,1.635 0.26,0.167 10 false 21 3.771,3.458 4.198,3.656 0.427,0.198 10 false 37 3.771,3.823 4.198,4.021 0.427,0.198 10 false 38 3.323,3.927 3.75,4.125 0.427,0.198 10 false CANL 3.313,3.552 3.74,3.75 0.427,0.198 10 false CANH 4.271,4.292 4.698,4.49 0.427,0.198 10 false O87 2.5,4.385 3.688,4.885 1.188,0.5 10 false Clearance Warning ECU Assembly 4.271,4.427 5.969,4.833 1.698,0.406 10 false No. 9 Global CAN Junction Connector 2.51,4.24 2.938,4.438 0.427,0.198 10 false O60 2.667,1.125 3.094,1.323 0.427,0.198 10 false BLB 6.385,1.125 6.813,1.323 0.427,0.198 10 false BRB 6.281,1.875 6.708,2.073 0.427,0.198 10 false BRGD 2.667,1.833 3.094,2.031 0.427,0.198 10 false BLGD 1.583,0.531 2.188,0.938 0.604,0.406 10 false ECU-IGR NO. 1 0.146,0.354 1.125,0.74 0.979,0.385 10 false from IG1-NO. 1 Relay 3.708,0.854 3.927,1.021 0.219,0.167 10 false 1 3.719,1.458 3.885,1.635 0.167,0.177 10 false 6 0.25,4.833 3.771,5.031 3.521,0.198 10 false *1: for TMC Made 0.25,5.198 3.771,5.396 3.521,0.198 10 false *2: for TMMF, TMMCZ Made

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 only is output A
DTC U117887 only is output B
DTC U117787 and U117887 are output C



A

3.CHECK VEHICLE TYPE

B

6.CHECK VEHICLE TYPE

C

9.CHECK CAN BUS MAIN WIRE
3.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)
a.

Disconnect the S6 blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-10 (BRGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S6-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
S6-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)
a.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-10 (BRGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O37-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
O37-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)

B

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)
a.

Disconnect the T6 blind spot monitor sensor LH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-10 (BLGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T6-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
T6-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)
a.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-10 (BLGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O38-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
O38-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CAN BUS MAIN WIRE
a.
E395856C17
1.49,2.792 1.938,3.031 0.448,0.24 0.24,1.448 0.635,1.708 0.396,0.26 1.073,2.948 1.26,2.948 1.26,2.948 1.604,3.417 true 2.333,3.917 2.49,4.302 2.49,4.302 2.635,4.302 true 1.833,1.854 2.365,2.583 2.365,2.583 2.51,2.583 true 1.844,1.604 2.573,0.771 2.573,0.771 2.719,0.771 true 0.24,2.708 0.552,2.865 0.313,0.156 10 false *b 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.625,2.823 1.979,3.021 0.354,0.198 10 false H3 0.292,1.49 0.698,1.688 0.406,0.198 10 false O87 2.781,0.708 3.271,0.906 0.49,0.198 10 false CANH 2.594,2.5 3.177,2.708 0.583,0.208 10 false CANL 2.698,4.208 3.281,4.417 0.583,0.208 10 false BAT 0.813,2.854 1.125,3.063 0.313,0.208 10 false CG
*a Component with harness connected
(No. 9 Global CAN Junction Connector)
*b Front view of DLC3


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
O87-9 (CANH) - O87-20 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
O87-9 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
O87-20 (CANL) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
O87-9 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
O87-20 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

10.CHECK FOR DTC

B

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

C

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

D

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
10.CHECK FOR DTC
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Clear DTCs
50002 438

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 and U117887 are not output A
DTC U117787 and U117887 are output B



A

B

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O87-9 (CANH) - O87-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-10 (CANH) - O87-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
O87-11 (CANH) - O87-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR

B

12.CHECK VEHICLE TYPE

C

14.CHECK VEHICLE TYPE

D

16.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
12.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

B

17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CA2P) - T6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

14.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

B

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - S6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

16.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O60-37 (CANH) - O60-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - O38-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - O37-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O87-9 (CANH) - O87-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-10 (CANH) - O87-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
O87-11 (CANH) - O87-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR

B

20.CHECK VEHICLE TYPE

C

22.CHECK VEHICLE TYPE

D

24.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
20.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

B

25.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CA2P) - T6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

22.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

23.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

B

26.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
23.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - S6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

24.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O60-37 (CANH) - O60-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

25.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - O38-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

26.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - O37-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O87-9 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-20 (CANL) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-9 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O87-20 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O87-10 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-21 (CANL) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-10 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O87-21 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O87-11 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-22 (CANL) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O87-11 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O87-22 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR

B

28.CHECK VEHICLE TYPE

C

30.CHECK VEHICLE TYPE

D

32.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
28.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

29.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

B

33.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
29.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CA2P) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T6-6 (CA2N) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T6-1 (CA2P) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T6-6 (CA2N) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

30.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

31.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

B

34.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
31.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
S6-6 (CA2N) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
S6-1 (CA2P) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S6-6 (CA2N) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

32.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O60-37 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O60-38 (CANL) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O60-37 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O60-38 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

33.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O38-6 (CA2N) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O38-1 (CA2P) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O38-6 (CA2N) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

34.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O37-6 (CA2N) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O37-1 (CA2P) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O37-6 (CA2N) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR)