Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2021.11
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0425251 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U023287  Lost Communication with Side Obstacle Detection Control Module "A" Missing Message  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (B) judges that there is a communication problem with the blind spot monitor sensor RH (A).

DTC No. Detection Item DTC Detection Condition Trouble Area
U023287 Lost Communication with Side Obstacle Detection Control Module "A" Missing Message The blind spot monitor sensor LH (B) cannot receive signals from the blind spot monitor sensor RH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in No. 9 global CAN junction connector*1

·

Open or short in No. 8 global CAN junction connector*2

·

Blind spot monitor sensor LH (B)

·

Power source circuit of blind spot monitor sensor RH (A)

·

Blind spot monitor sensor RH (A) ground circuit

·

Blind spot monitor sensor RH (A)



*1: for 5 Door

*2: for 3 Door


WIRING DIAGRAM

E334324E84
5.552,2.646 6.708,3.094 1.156,0.448 10 false Blind Spot Monitor Sensor LH (B) 2.25,2.677 3.417,3.135 1.167,0.458 10 false Blind Spot Monitor Sensor RH (A) 3.656,2.667 5.333,3.104 1.677,0.438 10 false No. 9 Global CAN Junction Connector 1.219,1.406 2.219,1.615 1,0.208 10 false ECU-IGR NO. 1 2.365,1.323 3.24,1.875 0.875,0.552 10 false BRB 2.917,0.99 3.792,1.542 0.875,0.552 10 false CA2P 5.688,0.99 6.563,1.542 0.875,0.552 10 false CA2P 5.688,1.854 6.563,2.406 0.875,0.552 10 false CA2N 2.938,1.854 3.813,2.406 0.875,0.552 10 false CA2N 2.333,1.885 3.208,2.438 0.875,0.552 10 false BRGD 3.656,2.49 4.104,2.708 0.448,0.219 10 false O87 5.542,2.458 6.542,2.667 1,0.208 10 false T6*1, O38*2 2.25,2.49 3.26,2.688 1.01,0.198 10 false S6*1, O37*2 4.875,1.833 5.75,2.385 0.875,0.552 10 false 22 3.865,1.844 4.26,2.094 0.396,0.25 10 false 21 3.854,1 4.135,1.344 0.281,0.344 10 false 10 4.875,0.99 5.75,1.542 0.875,0.552 10 false 11 2.156,1.156 3.031,1.708 0.875,0.552 10 false 5 2.083,1.792 2.958,2.344 0.875,0.552 10 false 10 3.417,1.844 4.292,2.396 0.875,0.552 10 false 6 5.469,0.979 6.344,1.531 0.875,0.552 10 false 1 3.375,0.99 4.25,1.542 0.875,0.552 10 false 1 5.479,1.854 6.354,2.406 0.875,0.552 10 false 6 0.115,1.229 0.896,1.656 0.781,0.427 10 false from IGR-NO. 1 Relay 0.125,3.031 2.313,3.271 2.188,0.24 10 false *1: for TMC Made 0.125,3.333 2.417,3.563 2.292,0.229 10 false *2: for TMMF, TMMCZ Made 0.115,0.104 2.135,0.344 2.021,0.24 12 false for 5 Door:

E334324E66
5.552,2.646 6.708,3.094 1.156,0.448 10 false Blind Spot Monitor Sensor LH (B) 2.25,2.677 3.417,3.135 1.167,0.458 10 false Blind Spot Monitor Sensor RH (A) 3.656,2.667 5.333,3.104 1.677,0.438 10 false No. 8 Global CAN Junction Connector 1.219,1.406 2.219,1.615 1,0.208 10 false ECU-IGR NO. 1 2.365,1.323 3.24,1.875 0.875,0.552 10 false BRB 2.917,0.99 3.792,1.542 0.875,0.552 10 false CA2P 5.688,0.99 6.563,1.542 0.875,0.552 10 false CA2P 5.688,1.854 6.563,2.406 0.875,0.552 10 false CA2N 2.938,1.854 3.813,2.406 0.875,0.552 10 false CA2N 2.333,1.885 3.208,2.438 0.875,0.552 10 false BRGD 3.656,2.49 4.104,2.708 0.448,0.219 10 false O113 5.542,2.458 6.542,2.667 1,0.208 10 false O38 2.26,2.49 3.271,2.688 1.01,0.198 10 false O37 4.875,1.833 5.75,2.385 0.875,0.552 10 false 22 3.865,1.844 4.26,2.094 0.396,0.25 10 false 21 3.854,1 4.135,1.344 0.281,0.344 10 false 10 4.875,0.99 5.75,1.542 0.875,0.552 10 false 11 2.156,1.156 3.031,1.708 0.875,0.552 10 false 5 2.083,1.792 2.958,2.344 0.875,0.552 10 false 10 3.417,1.844 4.292,2.396 0.875,0.552 10 false 6 5.469,0.979 6.344,1.531 0.875,0.552 10 false 1 3.375,0.99 4.25,1.542 0.875,0.552 10 false 1 5.479,1.854 6.354,2.406 0.875,0.552 10 false 6 0.115,1.229 0.896,1.656 0.781,0.427 10 false from IGR-NO. 1 Relay 0.115,0.104 2.135,0.344 2.021,0.24 12 false for 3 Door:

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for 5 Door A
for 3 Door B



A

2.CONFIRM MODEL

B

35.CHECK CAN BUS MAIN WIRE
2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Parking Support Brake System A
w/o Parking Support Brake System B



A

3.CHECK DTC OUTPUT (PARKING SUPPORT BRAKE SYSTEM)

B

4.CHECK CAN BUS MAIN WIRE
3.CHECK DTC OUTPUT (PARKING SUPPORT BRAKE SYSTEM)
a.

Using the GTS, check for DTCs according to the prompts on the screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Trouble Codes
50001 438
Standard:

The clearance warning ECU assembly does not output DTCs U117787 and U117887 simultaneously.



Result:
Proceed to
OK
NG



OK

4.CHECK CAN BUS MAIN WIRE

NG

GO TO PARKING SUPPORT BRAKE SYSTEM (DTC U117787)

4.CHECK CAN BUS MAIN WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E331798C33
0.135,1.583 0.552,1.854 0.417,0.271 0.875,2.094 0.417,2.865 true 0.865,1.833 0.531,1.042 true 0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.188,1.646 0.646,1.844 0.458,0.198 10 false O87 0.125,0.958 0.583,1.156 0.458,0.198 10 false CANH 0.25,2.906 0.708,3.104 0.458,0.198 10 false CANL
*a Component with harness connected
(No. 9 Global CAN Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
O87-11 (CANH) - O87-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
O87-11 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
O87-22 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
O87-11 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
O87-22 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



d.

Reconnect the cable to the negative (-) auxiliary battery terminal.


Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

5.CHECK VEHICLE TYPE

B

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

C

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)

D

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

B

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)
a.

Disconnect the S6 blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)
a.

Disconnect the S6 blind spot monitor sensor RH (A) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S6-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
S6-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)
a.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)
a.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O37-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
O37-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Check for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

11.REPLACE BLIND SPOT MONITOR SENSOR RH (A)
11.REPLACE BLIND SPOT MONITOR SENSOR RH (A)
a.

Replace the blind spot monitor sensor RH (A).

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor "B" > Clear DTCs
50002 460

Result:
Proceed to
NEXT



NEXT

13.RECHECK DTC
13.RECHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O87-11 (CANH) - O87-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
O87-10 (CANH) - O87-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH (A) CAN main wire) B
NG (to blind spot monitor sensor LH (B) CAN main wire) C



A

REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR

B

15.CHECK VEHICLE TYPE

C

18.CHECK VEHICLE TYPE
15.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

B

17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the S6 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - S6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - O37-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

18.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

19.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

B

20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
19.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the T6 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CA2P) - T6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - O38-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O87-11 (CANH) - O87-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
O87-10 (CANH) - O87-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH (A) CAN main wire) B
NG (to blind spot monitor sensor LH (B) CAN main wire) C



A

REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR

B

22.CHECK VEHICLE TYPE

C

25.CHECK VEHICLE TYPE
22.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

23.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

B

24.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
23.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the S6 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - S6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

24.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - O37-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

25.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

26.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

B

27.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
26.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the T6 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CA2P) - T6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

27.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - O38-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O87-11 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O87-22 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O87-11 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O87-22 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O87-10 (CANH) -Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O87-21 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O87-10 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O87-21 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH (A) CAN main wire) B
NG (to blind spot monitor sensor LH (B) CAN main wire) C



A

REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR

B

29.CHECK VEHICLE TYPE

C

32.CHECK VEHICLE TYPE
29.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made with 5 Door A
except TMC Made with 5 Door B



A

30.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

B

31.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
30.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the S6 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
S6-6 (CA2N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
S6-1 (CA2P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
S6-6 (CA2N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

31.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O37-6 (CA2N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O37-1 (CA2P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O37-6 (CA2N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

32.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

33.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

B

34.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
33.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the T6 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CA2P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T6-6 (CA2N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T6-1 (CA2P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
T6-6 (CA2N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

34.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O87 No. 9 global CAN junction connector.


b.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O38-6 (CA2N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O38-1 (CA2P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O38-6 (CA2N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

35.CHECK CAN BUS MAIN WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E331798C41
0.135,1.583 0.615,1.875 0.479,0.292 0.875,2.094 0.417,2.865 true 0.865,1.833 0.531,1.042 true 0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.208,1.646 0.667,1.844 0.458,0.198 10 false O113 0.125,0.958 0.583,1.156 0.458,0.198 10 false CANH 0.25,2.906 0.708,3.104 0.458,0.198 10 false CANL
*a Component with harness connected
(No. 8 Global CAN Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
O113-11 (CANH) - O113-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
O113-11 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
O113-22 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
O113-11 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
O113-22 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



d.

Reconnect the cable to the negative (-) auxiliary battery terminal.


Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

36.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

B

42.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR)

C

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR)

D

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR)
36.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)
a.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)
a.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O37-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
O37-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

38.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Check for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

39.REPLACE BLIND SPOT MONITOR SENSOR RH (A)
39.REPLACE BLIND SPOT MONITOR SENSOR RH (A)
a.

Replace the blind spot monitor sensor RH (A).

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

40.CLEAR DTC
40.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor "B" > Clear DTCs
50002 460

Result:
Proceed to
NEXT



NEXT

41.RECHECK DTC
41.RECHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

42.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O113-11 (CANH) - O113-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
O113-10 (CANH) - O113-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH (A) CAN main wire) B
NG (to blind spot monitor sensor LH (B) CAN main wire) C



A

REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR

B

43.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

C

44.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
43.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O113 No. 8 global CAN junction connector.


b.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - O37-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

44.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O113 No. 8 global CAN junction connector.


b.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - O38-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O113-11 (CANH) - O113-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
O113-10 (CANH) - O113-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH (A) CAN main wire) B
NG (to blind spot monitor sensor LH (B) CAN main wire) C



A

REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR

B

46.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

C

47.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
46.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O113 No. 8 global CAN junction connector.


b.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - O37-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

47.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O113 No. 8 global CAN junction connector.


b.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - O38-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O113-11 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O113-22 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O113-11 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O113-22 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O113-10 (CANH) -Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O113-21 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O113-10 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O113-21 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH (A) CAN main wire) B
NG (to blind spot monitor sensor LH (B) CAN main wire) C



A

REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR

B

49.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

C

50.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
49.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the O113 No. 8 global CAN junction connector.


b.

Disconnect the O37 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O37-1 (CA2P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O37-6 (CA2N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O37-1 (CA2P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O37-6 (CA2N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

50.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the O113 No. 8 global CAN junction connector.


b.

Disconnect the O38 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O38-1 (CA2P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O38-6 (CA2N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O38-1 (CA2P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O38-6 (CA2N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR