2005-2008 Yaris · Service Manual ENGINE

P0420 Catalyst System Efficiency Below Threshold (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

This vehicle has two heated oxygen sensors. One is located in front of the Three-Way Catalyst Converter (TWC), and the other is mounted behind the TWC. The output signals of the sensors are converted into waveforms inside the ECM. The front heated oxygen sensor is used by the ECM to monitor the air-fuel ratio, and its signal prompts the ECM to perform air-fuel ratio feedback control. As a result, the air-fuel ratio is balanced, and the waveform of the front heated oxygen sensor regularly oscillates between rich and lean. To determine whether or not the TWC performance has deteriorated, the ECM compares the waveforms of the front and rear heated oxygen sensors. While the TWC is functioning normally, the waveform of the rear heated oxygen sensor fluctuates between rich and lean more slowly than the front heated oxygen sensor's waveform. When the rear heated oxygen sensor's waveform frequently fluctuates, it indicates that the TWC performance has deteriorated.
A083860E05
DTC No.
DTC Detection Condition
Trouble Area
P0420
After engine and TWC warmed up, and while vehicle driven within set vehicle and engine speeds, waveform of Heated Oxygen (HO2) sensor (sensor 2) alternates frequently between rich and lean (3 trip detection logic)
  1. Gas leakage from exhaust system
  2. Heated oxygen sensor (sensor 1)
  3. Heated oxygen sensor (sensor 2)
  4. TWC

HINT:
DTC P0420 is detected when the vehicle is driven at an average vehicle speed of approximately 50 km/h (31 mph) with a city driving pattern for approximately 30 minutes, and then driven for approximately 15 minutes at a constant vehicle speed of between 70 km/h and 90 km/h (43 mph and 56 mph) with the transmission gear selector lever in the 5th position. (If the engine speed remains 1900 to 3400 rpm and the engine load remains 25 to 50 % after the catalyst is warmed up for 60 seconds or more, the detection for DTC P0420 will be performed)


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0420)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0420
    A
    P0420 and other DTCs
    B

    HINT:
    If any DTCs other than P0420 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (Control the Injection Volume for A/F Sensor)
  1. Perform the Active Test using the intelligent tester.

    HINT:
    The A/F Control operation lowers the injection volume by 12.5 % or increases the injection volume by 25 %.

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and turn the intelligent tester ON.

    3. Warm up the engine.

    4. Run the engine at 2,500 rpm for approximately 3 minutes.

    5. On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

    6. Select the following monitor items: O2S B1 S1 and O2S B1 S2.

    7. Perform the A/F Control operation with the engine in an idling condition (press the right or left button).

      Result:
      The heated oxygen sensor reacts in accordance with increases and decreases of the fuel injection volume:
      +25 % = Rich output:
      More than 0.5 V
      -12.5 % = Lean output:
      Less than 0.4 V

      NOTICE:
      1. Sensor 1 (front sensor) has an output delay of a few seconds.
      2. Sensor 2 (rear sensor) has maximum output delay of approximately 20 seconds.


      Output voltage of heated oxygen sensor (sensor 1: front sensor)
      Output voltage of heated oxygen sensor (sensor 2: rear sensor)
      Mainly suspected trouble area
      Case 1
      Injection volume
      +25 %
      -12.5 %
      A103184
      Injection volume
      +25 %
      -12.5 %
      A103184
      1. Catalyst
      2. Exhaust gas leakage
      Output voltage
      More than 0.5 V
      Less than 0.4 V
      A104056
      Output voltage
      More than 0.5 V
      Less than 0.4 V
      A104057
      Case 2
      Injection volume
      +25 %
      -12.5 %
      A103184
      Injection volume
      +25 %
      -12.5 %
      A103184
      Sensor 1: front sensor
      (sensor 1, heater, sensor 1 circuit)
      Output voltage
      Almost no reaction
      A103185
      Output voltage
      More than 0.5 V
      Less than 0.4 V
      A104057
      Case 3
      Injection volume
      +25 %
      -12.5 %
      A103184
      Injection volume
      +25 %
      -12.5 %
      A103184
      Sensor 2: rear sensor
      (sensor 2, heater, sensor 2 circuit)
      Output voltage
      More than 0.5 V
      Less than 0.4 V
      A104056
      Output voltage
      Almost no reaction
      A103185
      Case 4
      Injection volume
      +25 %
      -12.5 %
      A103184
      Injection volume
      +25 %
      -12.5 %
      A103184
      Extremely rich or lean actual air-fuel ratio (Injector, fuel pressure, gas leakage in exhaust system, etc.)
      Output voltage
      Almost no reaction
      A103185
      Output voltage
      Almost no reaction
      A103185
      The following procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors.To display the graph, select the following menu items on the tester: View / Line Graph.

      Result:
      Result
      Proceed To
      Case 1
      A
      Case 2
      B
      Case 3
      C
      Case 4
      D



B
REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

C
Go to step 4

D
CHECK AND REPLACE EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO, AND GO TO STEP 3
A


3. CHECK FOR EXHAUST GAS LEAKAGE


NG
REPAIR FOR EXHAUST GAS LEAKAGE PARTS
OK

REPLACE EXHAUST MANIFOLD

4. CHECK FOR EXHAUST GAS LEAKAGE


NG
REPAIR FOR EXHAUST GAS LEAKAGE PARTS
OK

REPLACE HEATED OXYGEN SENSOR (SENSOR 2)


← P0341 Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor) (+ P0342, P0343) (from Aug 2005)P0443 Evaporative Emission Control System Purge Control Valve Circuit Malfunction (from Aug 2005) →