2005-2008 Yaris · Service Manual ENGINE

P0341 Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed on the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes through the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.
DTC No.
DTC Detection Condition
Trouble Area
P0341
Abnormal pulse of camshaft position sensor occurs 12 times or more in 1 driving cycle (3 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Intake camshaft
  4. ECM
P0342
Camshaft position sensor output stays low (3 trip detection logic)
  1. Short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Intake camshaft
  4. ECM
P0343
Camshaft position sensor output stays high (3 trip detection logic)
  1. Open in camshaft position sensor circuit
  2. Short in power source circuit
  3. Camshaft position sensor
  4. Intake camshaft
  5. ECM
The correct waveform is as shown below.
G1 stands for the camshaft position sensor signal, and NE+ stands for the crankshaft position sensor signal.
Item
Contents
Terminal
CH1: G1 - E1
CH2: NE+ - NE-
Equipment Setting
5 V/Division, 20 ms/Division
Condition
While cranking or idling
A104034E06

HINT:
These DTCs are detected when the engine is running or the engine cranks 12 revolutions or more.


WIRING DIAGRAM

A109130E02

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
A120348E01
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    Camshaft position sensor (C40-1) - G- (C33-32)
    Below 1 Ω
    Camshaft position sensor (C40-2) - G1 (C33-13)
    Below 1 Ω
    Camshaft position sensor (C40-3) - VC2R (C33-74)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    Camshaft position sensor (C40-2) or G1 (C33-13) - Body ground
    10 kΩ or higher
    Camshaft position sensor (C40-3) or VC2R (C33-74) - Body ground
    10 kΩ or higher

  1. Reconnect the camshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
  1. Check the sensor installation.

    OK:
    The sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


3. INSPECT CAMSHAFT
  1. Check the teeth of the camshaft.

    OK:
    The teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT
OK


4. REPLACE CAMSHAFT POSITION SENSOR

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P0341, P0342 OR P0343)
  1. Start the engine.

  1. Stop the engine and wait for at least 10 seconds.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result:
    Specified Condition
    Proceed To
    No DTC output
    A
    P0341, P0342 or P0343
    B



B
REPLACE ECM
A

END


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (from Aug 2005)P0420 Catalyst System Efficiency Below Threshold (Bank 1) (from Aug 2005) →