2005-2008 Yaris · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is generated. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, fuel injection and ignition timing are controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
No crankshaft position sensor signal to ECM during the engine cranking (1 trip detection logic)
At this time, engine may not start.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (sensor plate)
  4. ECM
P0336
No missing teeth detected during engine cranking (34 teeth plus 2 missing teeth on crankshaft position sensor).
(3 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (sensor plate)
  4. ECM
P0336
The number of wave peaks of crankshaft position sensor signal is successively 1 more or 1 less during engine cranking.
(3 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (sensor plate)
  4. ECM
The correct waveform is shown below.
G1 stands for the camshaft position sensor signal, and NE+ stands for the crankshaft position sensor signal.
Item
Contents
Terminal
CH1: G1 - E1
CH2: NE+ - NE-
Equipment Setting
5 V/Division, 20 ms/Division
Condition
While cranking or idling
A104034E06

HINT:
  1. DTC P0335 is detected when the engine cranks 16 revolutions or more.
  2. DTC P0336 is detected when the engine cranks 8 revolutions or more.


WIRING DIAGRAM

A109130E02

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
The engine speed can be confirmed in the Data List using the intelligent tester (select the following menu items: Powertrain / Engine and ECT / Data List / Engine SPD). If there are no NE signals from the crankshaft position sensor despite the engine revolving, the engine speed is indicated as zero.

If the voltage output of the crankshaft position sensor is insufficient, the engine speed is indicated as lower than the actual engine rpm.

1. INSPECT CRANKSHAFT POSITION SENSOR (SENSOR RESISTANCE)
A105341E02
  1. Disconnect the crankshaft position sensor connector.

  1. Measure the crankshaft position sensor resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    1,850 to 2,450 Ω at 20°C (68°F)

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A120344E01
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    Crankshaft position sensor (C31-1) - NE+ (C33-60)
    Below 1 Ω
    Crankshaft position sensor (C31-2) - NE- (C33-81)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    Crankshaft position sensor (C31-1) or NE+ (C33-60) - Body ground
    10 kΩ or higher
    Crankshaft position sensor (C31-2) or NE- (C33-81) - Body ground
    10 kΩ or higher

  1. Reconnect the crankshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
  1. Check the crankshaft position sensor installation.

    OK:
    The sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4. CHECK CRANKSHAFT POSITION SENSOR PLATE
  1. Check the teeth of the sensor plate.

    OK:
    The plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT
OK


5. REPLACE CRANKSHAFT POSITION SENSOR

NEXT


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 OR P0336)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No DTC output
    A
    P0335 or P0336
    B



B
REPLACE ECM
A

END


← P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (from Aug 2005)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (from Aug 2005) →