DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built from Nov 2005
| EURO-OBD (EUROPE) |
Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
![]() ![]() |
The emission control system/components
The power train control components (which affect vehicle emissions)
The computer

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
To check DTCs, connect the intelligent tester to the Data Link Connector 3 (DLC3) of the vehicle.
The tester displays DTCs, the freeze frame data and a variety of engine data.
The DTCs and freeze frame data can be erased using the tester (Click here).
| M-OBD (EXCEPT EUROPEAN SPEC.) |
OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in:
![]() ![]() |
The emission control system/components
The power train control components (which affect vehicle emissions)
The computer
In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
| NORMAL MODE AND CHECK MODE |
| 2-TRIP DETECTION LOGIC |
| CHECK DLC3 |
The ECM uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

Symbol (Terminal No.)
Terminal Description
Condition
Specified Condition
SIL (7) - SG (5)
Bus "+" line
During transmission
Pulse generation
CG (4) - Body ground
Chassis ground
Always
Below 1 Ω
SG (5) - Body ground
Signal ground
Always
Below 1 Ω
BAT (16) - Body ground
Battery positive
Always
10 to 14 V
CANH (6) - CANL (14)
HIGH-level CAN bus line
Ignition switch off*
54 to 69 Ω
CANH (6) - CG (4)
HIGH-level CAN bus line
Ignition switch off*
200 Ω or more
CANL (14) - CG (4)
LOW-level CAN bus line
Ignition switch off*
200 Ω or more
CANH (6) - BAT (16)
HIGH-level CAN bus line
Ignition switch off*
6 kΩ or more
CANL (14) - BAT (16)
LOW-level CAN bus line
Ignition switch off*
6 kΩ or more
- NOTICE:
- *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.
- HINT:
-


- Connect the cable of an intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
- If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
- If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
- If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
- If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
| INSPECT BATTERY VOLTAGE |
- Battery Voltage:
- 11 to 14 V
| CHECK MIL |
Check that the MIL illuminates when the ignition switch is turned on (IG).
If the MIL does not illuminate, there is a problem in the MIL circuit (Click here).When the engine is started, the MIL should turn off.
