2005-2008 Yaris · Service Manual ENGINE

P0110 Intake Air Temperature Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

  1. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
  2. The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

  3. A067628E13
    Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, the voltage at terminal THA varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

    HINT:
    When the IAT sensor output is outside the normal range, the ECM determines this as a malfunction.

DTC No.
DTC Detection Conditions
Trouble Areas
P0110
Condition (a) or (b) continues for 2.0 seconds or more:
(a) IAT sensor output is less than -40°C (°F)
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
(b) IAT sensor output is more than 135°C (275°F)
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
*: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Open or short in IAT sensor circuit
  2. Short in power source circuit
  3. IAT sensor (built into MAF meter)
  4. ECM

HINT:
  1. When DTC P0110 is set, check the IAT by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.
  2. DTC P0110 is set when the engine idles for approximately 15 seconds.
Temperature Displayed
Malfunctions
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit


WIRING DIAGRAM

A112566E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    Same as actual Intake Air Temperature (IAT).

    Result:
    Temperature Displayed
    Proceed To
    -40 °C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual IAT
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A107690E06
    Disconnect the C26 Mass Air Flow (MAF) meter connector.

  1. Connect terminals THA and E2 of the MAF meter wire harness side connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher

  1. Reconnect the MAF meter connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER
NG


3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A122601E02
    Disconnect the C26 MAF meter connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THA (C26-4) - THA (C50-7)
    Below 1 Ω
    E2 (C26-5) - ETHA (C50-6)

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A084869E25
    Disconnect the C26 MAF meter connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the MAF meter connector.



OK
REPLACE MASS AIR FLOW METER
NG


5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A122601E03
    Disconnect the C26 MAF meter connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THA (C26-4) or THA (C50-7) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0101 Mass or Volume Air Flow Circuit Range / Performance Problem (from Nov 2005)P0115 Engine Coolant Temperature Circuit Malfunction (+ P0116) (from Nov 2005) →