2005-2008 Yaris · Service Manual ENGINE

P0101 Mass or Volume Air Flow Circuit Range / Performance Problem

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

Refer to DTC P0100 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0101
  1. Either of following conditions is met:
  1. MAF meter output does not change to less than 1.6 V within approximately 10 seconds of ignition switch being turned from on (IG) to off (while ECD relay is ON)
    (Determination of a malfunction is conducted within a given time after the ignition switch is turned from on (IG) to off. If a malfunction is detected within this time, the MIL is illuminated and a DTC is set when the ignition switch is next turned to on (IG))
  2. Actual value of MAF rate is implausible
    (The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
    *: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Open or short in mass air flow meter circuit
  2. Mass air flow meter
  3. Contamination in mass air flow meter
  4. EGR valve assembly
  5. Open or short in EGR circuit
  6. EGR passage
  7. Open or short in intake shutter control motor circuit
  8. Intake shutter
  9. Vacuum hose
  10. ECM

HINT:
This DTC is set in either of the following conditions:
  1. When the ignition switch is turned from off to on (IG).
  2. When the vehicle decelerates while driving.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0101
    A
    P0101 and other DTCs
    B

    HINT:
    If any DTCs other than P0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. CHECK CONNECTION OF VACUUM HOSES

HINT:
  1. Check the vacuum hose connection of the manifold absolute pressure sensor.
  2. Check that there is no air leak of the manifold absolute pressure sensor vacuum hose .

    OK:
    The vacuum hoses are appropriately connected to each other.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


3. READ VALUE USING INTELLIGENT TESTER (MAF)

NOTICE:
  1. Perform the inspection with the vehicle indoors and on a level surface.
  2. Perform the inspection of the MAF meter while it is installed to the air cleaner case (installed to the vehicle).
  3. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

  1. Turn the ignition switch on (IG).

    NOTICE:
    Do not run the engine.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Primary / MAF.

  1. Wait 30 seconds, and read the values on the tester.

    Standard:
    Less than 0.23 g/sec.



NG
REPLACE MASS AIR FLOW METER
OK


4. CHECK INTAKE AND EXHAUST SYSTEM
  1. Check for air leakage and any blockages between the air cleaner and the turbocharger.

  1. Check for air leakage and any blockages between the turbocharger and the intake manifold.

    OK:
    No air leakage or blockages.



NG
REPAIR OR REPLACE INTAKE AND EXHAUST SYSTEM
OK


5. INSPECT DIESEL THROTTLE BODY ASSEMBLY
A170630E01

NOTICE:
Perform this inspection with the engine off.

  1. Turn the ignition switch off.

  1. Remove the air cleaner hose.

  1. Visually confirm the position of the throttle valve in the diesel throttle body assembly.

    OK:
    Partially open

    If the valve is fully open or fully closed, replace the diesel throttle body assembly.

  1. Turn the ignition switch on.

  1. Visually confirm the position of the throttle valve in the diesel throttle body assembly.

    OK:
    Fully open

    If the result is not OK, replace the diesel throttle body assembly.

  1. Visually confirm the motion of the throttle valve in the diesel throttle body assembly when the ignition switch is turned from ON to OFF.

    OK:
    Throttle valve should move from fully open to fully closed and then to partially open.

    If the result is not OK, replace the diesel throttle body assembly.



NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY
OK


6. CHECK EGR VALVE ASSEMBLY

  1. A122610E02
    Disconnect C52 EGR valve connector.

  1. Measure the resistance between the terminals of the EGR valve connector.

    Standard resistance:
    Tester Connections
    Specified Conditions
    +B2 (5) - EGR1 (4)
    18.2 to 21.0 Ω at 20°C (68°F)
    +B2 (5) - EGR3 (6)
    +B1 (2) - EGR2 (1)
    +B1 (2) - EGR4 (3)



NG
REPLACE EGR VALVE ASSEMBLY
OK

REPLACE MASS AIR FLOW METER


← P0100 Mass or Volume Air Flow Circuit (from Nov 2005)P0110 Intake Air Temperature Circuit Malfunction (from Nov 2005) →