2005-2008 Yaris · Service Manual ENGINE

P0115 Engine Coolant Temperature Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor, of which the resistance value varies according to the ECT.
The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:
  1. When the ECT sensor output is outside the normal range, the ECM determines this as a malfunction.
  2. If DTC P0115 or P0116 is detected, the ECM performs engine control using an estimated ECT calculated from the IAT and the intake air volume at the time of engine start.

DTC No.
DTC Detection Conditions
Trouble Areas
P0115
Condition (a) or (b) continues for 2 seconds or more:
(a) ECT sensor output is less than -40°C (-40°F)
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
(b) ECT sensor output is more than 140°C (284°F)
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0116
  1. When ECT is less than 35°C (95°F) at engine start, ECT change in 240 seconds is less than 1°C (1.8°F) on the ECT sensor while the engine is highly loaded
    (The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*)
  2. When ECT is more than 98°C (208°F) at engine start, ECT sensor shows a change of less than 3°C (5.4°F) in 240 seconds while the engine load that is equal to that when the engine is idling
    (The MIL is illuminated and a DTC is set when the same malfunction is detected on 6 consecutive trips*)
    *: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. ECT sensor
  2. ECM

HINT:
  1. When DTC P0115 or P0116 is detected, check the ECT by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Coolant Temp.
  2. DTC P0115 is set when the engine idles for approximately 15 seconds.
  3. DTC P0116 is set when the vehicle idles for more than 5 minutes after driving at a vehicle speed of 100 to 120 km/h for more than 5 minutes.

Temperature Displayed
Malfunctions
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit

WIRING DIAGRAM

A112566E03

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ OUTPUT DTCS (DTC P0115 AND/OR P0116)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0115, or P0115 and P0116
    A
    P0116
    B



B
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
A


2. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    80°C to 100°C (176°F to 212°F) with warm engine.

    Result:
    Temperature Displayed
    Proceed To
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Between 80°C and 100°C (176°F and 212°F)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS
A


3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A107691E08
    Disconnect the C19 Engine Coolant Temperature (ECT) sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher.

  1. Reconnect the ECT sensor connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


4. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A122602E01
    Disconnect the C19 ECT sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THW (C19-2) - THW (C50-40)
    Below 1 Ω
    E2 (C19-1) - ETHW (C50-32)

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A084869E26
    Disconnect the C19 ECT sensor connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the ECT sensor connector.



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


6. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A122602E02
    Disconnect the C19 ECT sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THW (C19-2) or THW (C50-40) - Body ground
    10 kΩ or higher

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0110 Intake Air Temperature Circuit Malfunction (from Nov 2005)P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (+ P0487, P0488) (from Nov 2005) →