2005-2008 Yaris · Service Manual ENGINE

P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The ECM opens and closes the intake shutter valve (throttle valve) using the rotary solenoid type actuator. Upon opening and closing the valve, the exhaust gas recirculation volume is properly controlled. Also, engine vibration and noise are reduced by closing the valve when the engine is stopped.
DTC No.
DTC Detection Conditions
Trouble Areas
P0121
Learning value of intake shutter is abnormal
(Determination of a malfunction is conducted within a given time after the ignition switch is turned from on (IG) to off. If a malfunction is detected within this time, the MIL is illuminated and a DTC is set when the ignition switch is next turned to on (IG))
  1. Intake shutter stuck
  2. Intake shutter does not move smoothly
  3. Open or short in intake shutter circuit
  4. Open or short in intake shutter position sensor circuit
  5. Intake shutter position sensor (built into intake shutter valve)
  6. ECM
P0487
Open or short in intake shutter circuit
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in intake shutter circuit
  2. ECM
P0488
Target and actual positions of intake shutter are different
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Intake shutter stuck
  2. Intake shutter does not move smoothly
  3. Open or short in intake shutter circuit
  4. Open or short in intake shutter position sensor circuit
  5. Intake shutter position sensor (built into intake shutter valve)
  6. ECM

HINT:
  1. DTC P0121 is set when the ignition switch is turned from on (IG) to off.
  2. DTC P0487 is set when idling for more than 30 seconds after engine start.
  3. DTC P0488 is set when engine idling.


WIRING DIAGRAM

A122596E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0121, P0487 AND/OR P0488)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC output)
    Proceed To
    P0121, P0487 and/or P0488
    A
    P0121, P0487 and/or P0488, and P0122 and/or P0123
    B



B
GO TO DTC CHART
A


2. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3. INSPECT DIESEL THROTTLE BODY ASSEMBLY
A170630E01

NOTICE:
Perform this inspection with the engine off.

  1. Turn the ignition switch off.

  1. Remove the air cleaner hose.

  1. Visually confirm the position of the throttle valve in the diesel throttle body assembly.

    OK:
    Partially open

    If the valve is fully open or fully closed, replace the diesel throttle body assembly.

  1. Turn the ignition switch on.

  1. Visually confirm the position of the throttle valve in the diesel throttle body assembly.

    OK:
    Fully open

    If the result is not OK, replace the diesel throttle body assembly.

  1. Visually confirm the motion of the throttle valve in the diesel throttle body assembly when the ignition switch is turned from ON to OFF.

    OK:
    Throttle valve should move from fully open to fully closed and then to partially open.

    If the result is not OK, replace the diesel throttle body assembly.



NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (INTAKE SHUTTER (THROTTLE VALVE) - ECM)

  1. A122646E01
    Disconnect the C57 intake shutter connector.

  1. Disconnect the C50 ECM connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    DUTY (C57-1) - LUSL (C50-13)
    Below 1 Ω
    +B (C57-2) - Integration relay (1A-8)
    GND (C57-3) - Body ground

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    DUTY (C57-1) or LUSL (C50-13) - Body ground
    10 kΩ or higher
    +B (C57-2) or Integration relay (1A-8) - Body ground

  1. Reinstall the integration relay.

  1. Reconnect the intake shutter connector.

  1. Reconnect the ECM connector.



OK
REPLACE INTAKE SHUTTER ASSEMBLY
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0115 Engine Coolant Temperature Circuit Malfunction (+ P0116) (from Nov 2005)P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input (+ P0123) (from Nov 2005) →