2005-2008 Yaris · Service Manual ENGINE

P0115 Engine Coolant Temperature Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor.
The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:
When any of DTCs P0115, P0117 and P0118 are set, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.

DTC No.
Proceed to
DTC Detection Condition
Trouble Area
P0115
Step 1
Open or short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in engine coolant temperature sensor circuit
  1. Engine coolant temperature sensor
  1. ECM
P0117
Step 4
Short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Short in engine coolant temperature sensor circuit
  1. Engine coolant temperature sensor
  1. ECM
P0118
Step 2
Open in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open in engine coolant temperature sensor circuit
  1. Engine coolant temperature sensor
  1. ECM

HINT:
When any of these DTCs are set, check the engine coolant temperature by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F)
Short circuit

WIRING DIAGRAM

A148767E04

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard:
    Between 80°C and 100°C (176°F and 212°F) with warm engine.

    Result:
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F)
    B
    Between 80°C and 100°C (176°F and 212°F)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    1. If there is a short circuit, the intelligent tester indicates 140°C (284°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A107691E40
    Disconnect the engine coolant temperature sensor connector.

  1. Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard:
    140°C (284°F)

  1. Reconnect the engine coolant temperature sensor connector.



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A159444E01
    Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C19-2 - C20-97 (THW)
    Always
    Below 1 Ω
    C19-1 - C20-96 (ETHW)
    Always
    Below 1 Ω

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A084869E91
    Disconnect the engine coolant temperature sensor connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard:
    -40°C (-40°F)

  1. Reconnect the engine coolant temperature sensor connector.



NG
Go to step 5
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A159444E05
    Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C19-2 or C20-97 (THW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0110 Intake Air Temperature Circuit Malfunction (+ P0112, P0113) (from Nov 2006)P0116 Engine Coolant Temperature Circuit Range / Performance Problem (from Nov 2006) →