2005-2008 Yaris · Service Manual ENGINE

P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

HINT:
These DTCs relate to the Throttle Position (TP) sensor.

The Throttle Position (TP) sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions such as at high speeds and very low speeds.
The TP sensor has two sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.
A019802E71
DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Short in VTA1 circuit
  1. Open in VC circuit
  1. ECM
P0123
Output voltage of VTA1 4.535 V or more for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Open in VTA1 circuit
  1. Open in E2 circuit
  1. Short between VC and VTA1 circuits
  1. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Short in VTA2 circuit
  1. Open in VC circuit
  1. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Open in VTA2 circuit
  1. Open in E2 circuit
  1. Short between VC and VTA2 circuits
  1. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  1. Throttle position sensor (built into throttle body assembly)
  1. ECM

HINT:
  1. When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
  1. Throttle Position No. 1 denotes the VTA1 signal, and Throttle Position No. 2 denotes the VTA2 signal.

    Reference (Normal Condition):
    Tester Display
    Accelerator Pedal Fully Released
    Accelerator Pedal Fully Depressed
    Throttle Position No. 1
    0.5 to 1.1 V
    3.2 to 4.9 V
    Throttle Position No. 2
    2.1 to 3.1 V
    4.6 to 5.0 V


FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A148768E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION NO. 1 AND THROTTLE POSITION NO. 2)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

  1. Read the values.

    Result:
    When Accelerator Pedal Released
    When Accelerator Pedal Depressed
    Trouble Area
    Proceed to
    Throttle Position No. 1 (VTA1)
    Throttle Position No. 2 (VTA2)
    Throttle Position No. 1 (VTA1)
    Throttle Position No. 2 (VTA2)
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    VC circuit open
    A
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    E2 circuit open
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    2.4 V to 3.4 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    2.4 V to 3.4 V
    (Fail-safe)
    VTA1 circuit open or ground short
    0.7 V to 1.3 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    0.7 V to 1.3 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    VTA2 circuit open or ground short
    0.5 V to 1.1 V
    2.1 V to 3.1 V
    3.2 V to 4.9 V
    (Not fail-safe)
    4.6 V to 5.0 V
    (Not fail-safe)
    Throttle position sensor circuit normal
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

  1. A107944E18
    Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C17-5 (VC) - C20-67 (VCTA)
    Always
    Below 1 Ω
    C17-6 (VTA) - C20-115 (VTA1)
    Always
    Below 1 Ω
    C17-4 (VTA2) - C20-114 (VTA2)
    Always
    Below 1 Ω
    C17-3 (E2) - C20-91 (ETA)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C17-5 (VC) or C20-67 (VCTA) - Body ground
    Always
    10 kΩ or higher
    C17-6 (VTA) or C20-115 (VTA1) - Body ground
    Always
    10 kΩ or higher
    C17-4 (VTA2) or C20-114 (VTA2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VC VOLTAGE)

  1. A107895E18
    Disconnect the throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C17-5 (VC) - C17-3 (E2)
    Ignition switch on (IG)
    4.5 to 5.5 V

  1. Reconnect the throttle body connector.



NG
REPLACE ECM
OK


4. REPLACE THROTTLE BODY ASSEMBLY

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135
    A
    No output
    B



B
END
A

REPLACE ECM


← P0116 Engine Coolant Temperature Circuit Range / Performance Problem (from Nov 2006)P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (from Nov 2006) →