2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. CLEAN QUARTER WINDOW GLASS

BO04421E01
  1. Clean the outer circumference of the glass with white gasoline.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Even if using a new glass, clean the glass with white gasoline.

    HINT:
    Since the pin is for positioning the glass, there is no need to replace it with a new one when reusing the glass, even if damaged.


2. CLEAN VEHICLE BODY

  1. B073084E02
    Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.


3. INSTALL QUARTER WINDOW GLASS SPACER

B118063
  1. Coat the installation parts of the spacers with Primer G.

  1. Install 3 new spacers onto the glass, as shown in the illustration.


4. INSTALL QUARTER WINDOW MOULDING OUTSIDE FRONT

B121547E01
  1. Using a brush or sponge, apply Primer G to the edge of the quarter window and contact surface.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. Install the quarter window moulding outside front, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    9.5 mm (0.374 in.)


5. INSTALL QUARTER WINDOW GLASS

H002865E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

  1. B116963E01
    Using a brush or sponge, apply Primer G to the edge of the quarter window and contact surface.

    Specification:
    Area
    Measurement
    a
    6.0 mm (0.236 in.)
    b
    14 mm (0.551 in.)
    c
    7.5 mm (0.295 in.)
    d
    22 mm (0.866 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. B116964E01
    Apply adhesive.

    Adhesive:
    Part No. 08850-00801 or the equivalent


    1. Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      13 mm (0.512 in.)
      d
      14.5 mm (0.571 in.)
      e
      8 mm (0.315 in.)

  1. Install the quarter window glass onto the body.

    1. Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the pins are attached to the body correctly.
      3. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.

    3. B073131E02
      Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the quarter window glass rim.

      NOTICE:
      Do not to drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


6. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leakage with auto glass sealer.


7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

E116754
  1. Engage the 8 clips, retainer and 10 claws and install the quarter trim panel front.

  1. E116753
    Pass the belt of the rear seat outer belt through the rear seat shoulder belt hanger.


8. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (for Sill Bar Type)

E116763
  1. Install the front seat outer belt bar with the 2 bolts.


9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Install the front door opening trim weatherstrip.


10. INSTALL FRONT DOOR SCUFF PLATE

E116758
  1. Engage the 8 claws and install the front door scuff plate.


11. INSTALL REAR SEAT ASSEMBLY
  1. for RH Side:

    1. Install the rear seat assembly (Click here).

  1. for LH Side:

    1. Install the rear seat assembly (Click here).


12. INSTALL NO. 2 REAR SEAT LEG COVER (for LH Side)

  1. B114739
    Engage the 3 claws and install the No. 2 rear seat leg cover.


13. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover (Click here).

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover (Click here).


14. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


15. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


16. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B119913
    Install the spare wheel cover.


17. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


18. INSTALL REAR FLOOR CARPET ASSEMBLY

  1. B119912
    Install the rear floor carpet.


19. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Aug 2005)PRECAUTION (from Aug 2005) →