2005-2008 Yaris · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2005

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.

2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.


3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106371
    Release the 2 knobs and remove the deck board.


4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B119913
    Remove the spare wheel cover.


5. REMOVE DECK FLOOR BOX RH (w/ Deck Board)

  1. B106372
    Release the 2 knobs and remove the deck floor box.


6. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B119912
    Remove the rear floor carpet.


8. REMOVE NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Remove the No. 1 rear seat leg cover (Click here).

  1. for LH Side:

    1. Remove the No. 1 rear seat leg cover (Click here).


9. REMOVE NO. 2 REAR SEAT LEG COVER (for LH Side)

  1. B126921E01
    Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.


10. REMOVE REAR SEAT ASSEMBLY
  1. for RH side:

    1. Remove the rear seat assembly (Click here).

  1. for LH Side:

    1. Remove the rear seat assembly (Click here).


11. REMOVE FRONT DOOR SCUFF PLATE

E116758
  1. Disengage the 8 claws and remove the front scuff plate.


12. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Separate the front door opening trim weatherstrip.


13. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (for Sill Bar Type)

E116763
  1. Remove the 2 bolts and the front seat outer belt bar.


14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY

E116753
  1. Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.

  1. E116754
    Disengage the 8 clips, retainer and 10 claws and remove the quarter trim panel.


15. REMOVE QUARTER WINDOW MOULDING OUTSIDE FRONT

B116961E01
  1. Using a knife, cut off the quarter window moulding outside front.

    NOTICE:
    Do not damage the vehicle body with the knife.

    HINT:
    Make a partial cut in the quarter window moulding outside front. Then pull and remove it by hand.


16. REMOVE QUARTER WINDOW GLASS

B116962E01
  1. Apply protective tape to the outer circumference of the quarter window, as shown in the illustration.

  1. From the interior, insert piano wires between the vehicle body and quarter window, as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    When separating the quarter window from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.

  1. Cut through the adhesive by pulling the piano wire around the quarter window.

← COMPONENTS (from Aug 2005)INSTALLATION (from Aug 2005) →