2005-2008 Yaris · Service Manual ENGINE

P0560 System Voltage

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and set the DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back-up power source circuit
(1 trip detection logic)
  1. Open in back-up power source circuit
  2. Battery
  3. Battery terminals
  4. EFI fuse
  5. ECM

HINT:
If DTC P0560 is set, the ECM does not store other DTCs or the data stored in the ECM are partly erased.


WIRING DIAGRAM

A159164E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT FUSE (EFI FUSE)

  1. A112606E02
    Remove the EFI fuse from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI fuse
    Always
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (EFI FUSE - ECM)

  1. A107903E03
    Disconnect the ECM connector.

  1. Remove the EFI fuse from engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    2 (EFI fuse) - A21-20 (BATT)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    2 (EFI fuse) or A21-20 (BATT) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the EFI fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (EFI FUSE - BATTERY)

  1. A159769E01
    Remove the EFI fuse from engine room R/B and J/B.

  1. Disconnect the negative battery terminal.

  1. Disconnect the positive battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    1 (EFI fuse) - Battery positive terminal
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    1 (EFI fuse) - Battery positive terminal - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the EFI fuse.

  1. Reconnect the positive battery terminal.

  1. Reconnect the negative battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT BATTERY
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Battery terminals
    20°C (68°F)
    12.5 to 12.9 V



NG
REPLACE BATTERY
OK


5. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Turn the ignition switch off and turn the tester off.

  1. Start the engine and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT/ DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0560
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM


← P0505 Idle Control System Malfunction (from Nov 2006)P0604 Internal Control Module Random Access Memory (RAM) Error (+ 5 more codes) (from Nov 2006) →