2005-2008 Yaris · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

The cranking holding control system keeps energizing the starter relay from when the ECM detects the starter signal (STSW signal) from the ignition switch or the main body ECU until the ECM performs a judgement of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal.
Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.
A103821E16
While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter signal (STA signal) while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
Following conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic):
  1. (a) Vehicle speed more than 20 km/h (12.4 mph)
  2. (b) Engine speed more than 1,000 rpm
  3. (c) STA signal ON
  1. Clutch start switch
  2. Starter relay circuit
  3. Ignition switch *1
  4. Main body ECU *2
  5. ECM
*1: Without Entry and Start System
*2: With Entry and Start System

WIRING DIAGRAM

A159154E01
A159155E01

INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STARTER RELAY)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active test / Activate the Starter Relay.

  1. Select the following monitor item: Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is on (IG) and the engine starts.

    Result:
    Condition
    Starter Signal
    Ignition switch on (IG)
    OFF
    Engine start
    ON

    Result:
    Result
    Proceed to
    Within standard range
    A
    Outside standard range (vehicle without entry and start system)
    B
    Outside standard range (vehicle with entry and start system)
    C



B
Go to step 2

C
Go to step 6
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

  1. A159450E01
    Disconnect the clutch start switch connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch on (IG).

    Result:
    Starter Signal
    Proceed to
    ON
    A
    OFF
    B

  1. Reconnect the clutch start switch connector.



B
Go to step 4
A


3. INSPECT ECM (STA TERMINAL VOLTAGE)
A122539E03
  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    STA (A21-48) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A
    Below 1.5 V
    B

  1. Reconnect the clutch start switch connector.

  1. Reconnect the ECM connector.



B
REPLACE ECM
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH - ST RELAY)

4. INSPECT CLUTCH START SWITCH
A159771E01
  1. Disconnect the clutch start switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    OFF (free)
    10 kΩ or higher

  1. Reconnect the clutch start switch connector.



NG
REPLACE CLUTCH START SWITCH AND GO TO STEP 5
OK


5. INSPECT IGNITION SWITCH
A107906E07
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (AM1) - 7 (ST2)
    ON position
    10 kΩ or higher
    5 (AM2) - 7 (ST2)

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH - IGNITION SWITCH AND ECM)

6. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

  1. A159450E01
    Disconnect the clutch start switch connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch on (IG).

    Result:
    Starter Signal
    Proceed to
    ON
    A
    OFF
    B

  1. Reconnect the clutch start switch connector.



B
Go to step 8
A


7. INSPECT ECM (STA TERMINAL VOLTAGE)
A122539E03
  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    STA (A21-48) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A
    Below 1.5 V
    B

  1. Reconnect the clutch start switch connector.

  1. Reconnect the ECM connector.



B
REPLACE ECM
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH - ST RELAY)

8. INSPECT CLUTCH START SWITCH
A159771E01
  1. Disconnect the clutch start switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    OFF (free)
    10 kΩ or higher

  1. Reconnect the clutch start switch connector.



NG
REPLACE CLUTCH START SWITCH AND GO TO STEP 9
OK


9. INSPECT STARTER CUT RELAY (TERMINAL VOLTAGE)
A159451E01
  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    ST CUT relay (D67-3) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A
    ST CUT relay (D67-5) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B

  1. Reinstall the ST CUT relay.



B
Go to step 12
A


Go to step 11

10. CHECK HARNESS AND CONNECTOR (ECM - ST CUT RELAY)
A159452E01
  1. Disconnect the ECM connector.

  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    ST CUT relay (D67-3) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A
    Ignition switch on (IG)
    Below 1.5 V
    B

  1. Reconnect the ECM connector.

  1. Reinstall the ST CUT relay.



B
REPLACE ECM
A


11. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU - ST CUT RELAY)
A159453E01
  1. Disconnect the ECM connector.

  1. Disconnect the main body ECU connector.

  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    ST CUT relay (D67-3) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A
    Ignition switch on (IG)
    Below 1.5 V
    B

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connector.

  1. Reinstall the ST CUT relay.



B
REPLACE MAIN BODY ECU
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

12. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ST CUT RELAY)
A159454E01
  1. Disconnect the main body ECU connector.

  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    ST CUT relay (D67-5) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A
    Ignition switch on (IG)
    Below 1.5 V
    B

  1. Reconnect the main body ECU connector.

  1. Reinstall the ST CUT relay.



B
REPLACE MAIN BODY ECU
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0604 Internal Control Module Random Access Memory (RAM) Error (+ 5 more codes) (from Nov 2006)P0724 Brake Switch "B" Circuit High (from Nov 2006) →