P0335 Crankshaft Position Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built from Nov 2006
Also covers:
- P0339 Crankshaft Position Sensor "A" Circuit Intermittent
DESCRIPTION
The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet.The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0335 |
When either following conditions met:
|
|
| P0339 |
Following conditions (a), (b) and (c) met (1 trip detection logic): (a) Engine speed 1,000 rpm or more (b) No crankshaft position sensor signal for 0.05 seconds or more (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
- Check the engine speed. The engine speed can be checked by using an intelligent tester. Follow the procedure below:
- Connect the intelligent tester to the DLC3.
- Start the engine.
- Turn the tester on.
- Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
- The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
| 1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the value displayed on the tester while the engine is running.
- OK:
- Correct value is displayed.
- HINT:
- To check the engine speed change, display the graph on the tester.
- If the engine does not start, check the engine speed while cranking.
- If the engine speed indicated on the tester remains zero(0), there may be an open or short in the crankshaft position sensor circuit.
- To check the engine speed change, display the graph on the tester.
|
|
||||
| OK | ||
| ||
| 2. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
Disconnect the crankshaft position sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
1850 to 2450 Ω
Reconnect the crankshaft position sensor connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Condition
Specified Condition
C2-1 (NE+) - C20-122 (NE+)
Always
Below 1 Ω
C2-2 (NE-) - C20-121 (NE-)
Always
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Condition
Specified Condition
C2-1 (NE+) or C20-122 (NE+) - Body ground
Always
10 kΩ or higher
C2-2 (NE-) or C20-121 (NE-) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the crankshaft position sensor connector.
|
|
||||
| OK | |
| 4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the crankshaft position sensor installation condition.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 5. CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the sensor plate.
- OK:
- Sensor plate does not have any cracks or deformation.
|
|
||||
| OK | ||
| ||
