2005-2008 Yaris · Service Manual ENGINE

P0100 Mass or Volume Air Flow Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.

A094565E06

HINT:
  1. When the MAF meter output is outside the normal range, the ECM determines this as a malfunction.
  2. DTC P0100 is set while idling for 10 seconds or more after the engine was revved up to 3,000 rpm.

DTC No.
DTC Detection Conditions
Trouble Areas
P0100
Condition (a) or (b) continues for 2.0 seconds or more:
(a) VG less than 0.14 V
(b) VG more than 4.8 V
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. Contamination in MAF meter
  4. ECM

HINT:
When any of these DTCs are set, check the air-flow rate by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / MAF.
Mass Air Flow Rate (g/sec)
Malfunctions
Approximately 0.3 or less
  1. Open in Mass Air Flow (MAF) meter power source circuit
  2. Open or short in VG circuit
110.0 or more
  1. Open in EVG circuit


WIRING DIAGRAM

A122591E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the values displayed on the tester.

    Result:
    Mass Air Flow Rate (g/sec)
    Proceed To
    0.3 or less
    A
    110.0 or more
    B
    Between 1.0 and 109.0 (*1)
    C

    *1: The value must be changed when the throttle valve is open or closed with the engine running.



B
Go to step 7

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

  1. A054396E39
    Disconnect the C26 Mass Air Flow (MAF) meter connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +B (C26-1) - Body ground
    9 to 14 V

  1. Reconnect the MAF meter connector.



NG
Go to step 5
OK


3. INSPECT MASS AIR FLOW METER (VG VOLTAGE)

  1. A112625E04
    Output voltage inspection.
    1. Disconnect the C26 MAF meter connector.

    2. Apply battery voltage across terminals +B and E2G.

    3. Connect the positive (+) tester prove to terminal VG, and negative (-) tester prove to terminal E2G.

    4. Measure the voltage.

      Standard voltage:
      Tester Connections
      Specified Conditions
      VG (3) - E2G (2)
      0.14 to 4.8 V

    5. Reconnect the MAF meter connector.



NG
REPLACE MASS AIR FLOW METER
OK


4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A122601E01
    Disconnect the C26 MAF meter connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VG (C26-3) - VG (C50-36)
    Below 1 Ω
    E2G (C26-2) - EVG (C50-15)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VG (C26-3) or VG (C50-36) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
CHECK ECM POWER SOURCE CIRCUIT
OK

REPLACE ECM

5. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)

  1. A107943E01
    Disconnect the C26 MAF meter connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (C26-1) - Integration Relay (1A-8)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (C26-1) or Integration Relay (1A-8) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT

7. CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

  1. A107942E01
    Disconnect the C26 MAF meter connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    E2G (C26-2) - Body ground
    Below 1 Ω

  1. Reconnect the MAF meter connector.



OK
REPLACE MASS AIR FLOW METER
NG


8. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A122601E01
    Disconnect the C26 MAF meter connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VG (C26-3) - VG (C50-36)
    Below 1 Ω
    E2G (C26-2) - EVG (C50-15)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VG (C26-3) or VG (C50-36) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0089 Pressure Control Valve Plausibility to Consume Current High Intensity (+ P1271) (from Nov 2005)P0101 Mass or Volume Air Flow Circuit Range / Performance Problem (from Nov 2005) →