2005-2008 Yaris · Service Manual ENGINE

P0089 Pressure Control Valve Plausibility to Consume Current High Intensity

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

Based on signals from the ECM, the pressure control valve opens when sudden deceleration occurs, or when the ignition switch is off, to prevent the fuel pressure from becoming too high.
DTC No.
DTC Detection Conditions
Trouble Areas
P0089
  1. Open or short in pressure control valve circuit (DTC P1271 set simultaneously)
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  2. ECM internal error (DTC P1271 not set)
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in pressure control valve circuit
  2. Common rail assembly (pressure control valve)
  3. ECD2 fuse
  4. ECM
P1271
  1. Open or short in pressure control valve circuit
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)

HINT:
These DTCs are set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

A122652E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ OUTPUT DTCS (DTC P0089 AND/OR P1271)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P1271, or P0089 and P1271
    A
    Only P0089
    B



B
REPLACE ECM
A


2. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3. INSPECT COMMON RAIL ASSEMBLY (PRESSURE CONTROL VALVE ASSEMBLY)

  1. A122654E01
    Disconnect the C53 pressure control valve connector.

  1. Measure the resistance between the terminals of the pressure control valve.

    Standard resistance:
    3.42 to 3.78 Ω at 20°C (68°F)

  1. Reconnect the pressure control valve connector.



NG
REPLACE COMMON RAIL ASSEMBLY (PRESSURE CONTROL VALVE)
OK


4. CHECK HARNESS AND CONNECTOR (ECM - PRESSURE CONTROL VALVE - ECD RELAY)

  1. A122651E01
    Disconnect the C53 pressure control valve connector.

  1. Disconnect the C50 ECM connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    PRV (C50-4) - PRV (C53-1)
    Below 1 Ω
    Integration relay (1A-8) - +B (C53-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    PRV (C50-4) or PRV (C53-1) - Body ground
    10 kΩ or higher
    Integration relay (1A-8) or +B (C53-2) - Body ground

  1. Reconnect the pressure control valve connector.

  1. Reconnect the ECM connector.

  1. Reinstall the integration relay.



OK
REPLACE ECM
NG

CHECK ECM POWER SOURCE CIRCUIT


← P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance (+ P0605, P1633) (from Nov 2005)P0100 Mass or Volume Air Flow Circuit (from Nov 2005) →