2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built from Aug 2005

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.

HINT:
The procedure listed below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL REAR SPEAKER ASSEMBLY

E107776
  1. Engage the 2 claws of the speaker with the body and provisionally install the speaker.

  1. E107777E01
    Using an air riveter or hand riveter, install the front No. 1 speaker assembly onto the front door panel with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. H002440
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. H002441
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. H002442
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.

  1. E107778
    Connect the connector.


2. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

E116754
  1. Engage the 8 clips, retainer and 10 claws and install the quarter trim panel front.

  1. E116753
    Pass the belt of the rear seat outer belt through the rear seat shoulder belt hanger.


3. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (w/ Seat Belt Bar)

E116763
  1. Install the front seat outer belt bar with the 2 bolts.


4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Install the front door opening trim weatherstrip.


5. INSTALL FRONT DOOR SCUFF PLATE

E116758
  1. Engage the 8 claws and install the front door scuff plate.


6. INSTALL REAR SEAT ASSEMBLY
  1. for RH Side:

    1. Install the rear seat assembly (Click here ).

  1. for LH Side:

    1. Install the rear seat assembly (Click here ).


7. INSTALL NO. 2 REAR SEAT LEG COVER (for LH Side)

  1. B114739
    Engage the 3 claws and install the No. 2 rear seat leg cover.


8. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover (Click here ).

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover (Click here ).


9. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


10. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


11. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B119913
    Install the spare wheel cover.


12. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


13. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B119912
    Install the rear floor carpet.


14. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Aug 2005)COMPONENTS (from Jan 2006) →