2005-2008 Yaris · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built from Aug 2005

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.

HINT:
The procedure listed below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.


3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106371
    Release the 2 knobs and remove the deck board.


4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B119913
    Remove the spare wheel cover.


5. REMOVE DECK FLOOR BOX RH (w/ Deck Board)

  1. B106372
    Release the 2 knobs and remove the deck floor box.


6. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B119912
    Remove the rear floor carpet.


8. REMOVE NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Remove the No. 1 rear seat leg cover (Click here ).

  1. for LH Side:

    1. Remove the No. 1 rear seat leg cover (Click here ).


9. REMOVE NO. 2 REAR SEAT LEG COVER (for LH Side)

  1. B126921E01
    Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.


10. REMOVE REAR SEAT ASSEMBLY
  1. for RH side:

    1. Remove the rear seat assembly (Click here ).

  1. for LH Side:

    1. Remove the rear seat assembly (Click here ).


11. REMOVE FRONT DOOR SCUFF PLATE

E116758
  1. Disengage the 8 claws and remove the front scuff plate.


12. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Separate the front door opening trim weatherstrip.


13. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (w/ Seat Belt Bar)

E116763
  1. Remove the 2 bolts and the front seat outer belt bar.


14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY

E116753
  1. Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.

  1. E116754
    Disengage the 8 clips, retainer and 10 claws and remove the quarter trim panel.


15. REMOVE REAR SPEAKER ASSEMBLY

  1. E107775
    Disconnect the connector.

  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the rear speaker assembly from the quarter panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the quarter panel.

← ON-VEHICLE INSPECTION (from Aug 2005)INSTALLATION (from Aug 2005) →