2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL REAR SPEAKER ASSEMBLY

  1. B134975
    Install the rear speaker with the 4 bolts.

  1. Connect the speaker connector.


2. INSTALL PACKAGE TRAY TRIM PAD

  1. B134974
    Install the package tray trim pad.


3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

  1. B134912
    for 3 Point Type Rear Center Seat Belt:

    1. Engage the 5 claws and install the package tray trim.

    2. Install the 4 clips.

  1. B134913
    for 2 Point Type Rear Center Seat Belt:

    1. Engage the 5 claws and install the package tray trim.

    2. Install the 3 clips.


4. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY (w/o Rear Spoiler)

  1. E127792
    Connect the connector.

  1. Engage the 4 claws and install the high mounted stop light assembly.


5. INSTALL ROOF SIDE INNER GARNISH RH

  1. B134775E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B134774
    w/o Curtain Shield Airbag:

    1. Engage the 4 clips and the claw and install the roof side inner garnish.


6. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.


7. INSTALL REAR SEAT SIDE COVER RH

  1. B134776
    Engage the 2 clips and the 4 claws and install the rear seat side cover.


8. INSTALL REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.


9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B138636
    Install the rear door opening trim weatherstrip.


10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


11. INSTALL REAR DOOR SCUFF PLATE RH

  1. B134771
    Engage the 7 claws and install the rear door scuff plate.


12. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


13. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)

B136275
  1. Install the luggage compartment trim inner pad.


14. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)

B136270
  1. Install the spare wheel cover.


15. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)

B136269
  1. Install the luggage compartment floor mat.


16. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)

  1. B134945E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134944
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134943
    Install the rear seat outer belt into the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Seat Belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


17. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)

  1. B134926E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134925
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134924
    Install the rear seat outer belt into the rear seat shoulder belt guide.


18. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B134981
    Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }

  1. B138450E01
    Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


19. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).

  1. for Fixed Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →