2005-2008 Yaris · Service Manual BRAKE

C0200/31 Right Front Wheel Speed Sensor Signal

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.
C115116E03
DTC No.
DTC Detecting Conditions
Trouble Areas
C0200/31
C0205/32
When any of following conditions detected:
  1. When vehicle speed 15 km/h (9 mph) or more, wheel speed 6 km/h (4 mph) or less.
  2. At vehicle speed of 45 km/h (28 mph) or more, open in sensor harness occurs intermittently for 0.2 seconds or more.
  3. When vehicle speed between 10 km/h (6 mph) and 15 km/h (9 mph) for 3 minutes, one wheel speed 0 km/h (0 mph).
  4. Pressure reduction mode of ABS system lasts for 28 seconds or more.
  5. When vehicle driven at speed of 20 km/h (12 mph) or more, difference between wheel speeds indicated by two sensors twice or more for 30 seconds or more.
  6. Foreign matter adheres to sensor rotor.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1271/71
C1272/72
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1275/75
C1276/76
Detected only during test mode.
  1. Front speed sensor (open)
  2. Front speed sensor circuit (open)
C1330/35
C1331/36
Open in front speed sensor circuit continues for 0.15 seconds or more.
  1. Front speed sensor (open)
  2. Front speed sensor circuit (open)

HINT:
  1. DTCs C0200/31 and C1330/35 relate to the front speed sensor RH.
  2. DTCs C0205/32 and C1331/36 relate to the front speed sensor LH.


WIRING DIAGRAM

C117849E05

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in test mode after cleaning or replacement (Click here).


1. READ VALUE OF DATA LIST (FRONT SPEED SENSOR)

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Start the engine and drive the vehicle.

  1. Turn the tester on.

  1. Read the wheel speed value using the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

  1. Select the item "FR (FL) Wheel Speed" in the DATA LIST and read the value displayed on the intelligent tester.

    DATA LIST: ABS/VSC/TRC 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    FR Wheel Speed
    Wheel speed sensor (FR) reading : min.: 0 km/h (0 mph), max.: 300 km/h (186 mph)
    Similar to speed indicated on speedometer
    FL Wheel Speed
    Wheel speed sensor (FL) reading : min.: 0 km/h (0 mph), max.: 300 km/h (186 mph)
    Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference in the displayed speed values.

    HINT:
    There is a tolerance of +- 10% in the speedometer indication.



NG
Go to step 4
OK


2. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTC output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


3. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 10
A

END

4. CHECK FRONT SPEED SENSOR INSTALLATION
  1. Check that the speed sensor installation bolt is tightened properly.

    OK:
    The installation bolt is tightened properly.

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



NG
TIGHTEN BOLT PROPERLY
OK


5. CHECK FRONT SPEED SENSOR

  1. BR03795E09
    Visually check the speed sensor for deformation and damage.

    OK:
    No deformation or damage.
    There is no gap between the sensor and front steering knuckle.



NG
REPLACE FRONT SPEED SENSOR
OK


6. CHECK SPEED SENSOR TIP
  1. Remove the speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE SPEED SENSOR
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

  1. C129345E01
    Confirm that the skid control ECU connector and speed sensor connector are properly connected.

  1. Disconnect the skid control ECU connector and the front speed sensor connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance.

    Standard Resistance (LH):
    Tester Connection
    Specified Condition
    A39-22 (FL+) - A11-2 (FL+)
    Below 1 Ω
    A39-21 (FL-) - A11-1 (FL-)
    Below 1 Ω

    Standard Resistance (RH):
    Tester Connection
    Specified Condition
    A39-18 (FR+) - A7-2 (FR+)
    Below 1 Ω
    A39-19 (FR-) - A7-1 (FR-)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE)

  1. C129353E01
    Disconnect the speed sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard Voltage (LH):
    Tester Connection
    Specified Condition
    A11-2 (FL+) - Body ground
    5.7 to 17.3 V

    Standard Voltage (RH):
    Tester Connection
    Specified Condition
    A7-2 (FR+) - Body ground
    5.7 to 17.3 V



NG
REPLACE BRAKE ACTUATOR
OK


9. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


10. REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor.


NEXT


11. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR


← ON-VEHICLE INSPECTION (from Nov 2005)C0210/33 Right Rear Wheel Speed Sensor Signal (+ 7 more codes) (from Nov 2005) →