2005-2008 Yaris · Service Manual BRAKE

C0210/33 Right Rear Wheel Speed Sensor Signal

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

Refer to DTC C0200/31 (Click here).
DTC No.
DTC Detecting Conditions
Trouble Areas
C0210/33
C0215/34
When any of following conditions detected:
  1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph) or less.
  2. At vehicle speed of 45 km/h (28 mph) or more, open in sensor harness occurs intermittently for 0.2 seconds or more.
  3. When vehicle speed between 10 km/h (6 mph) and 15 km/h (9 mph) for 3 minutes, one wheel speed 0 km/h (0 mph).
  4. Pressure reduction mode of ABS system lasts for 28 seconds or more.
  5. When vehicle driven at speed of 20 km/h (12 mph) or more, difference between wheel speeds indicated by two sensors twice or more for 30 seconds or more.
  6. Foreign matter adheres to sensor rotor.
  1. Skid control sensor
  2. Skid control sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1273/73
C1274/74
Detected only during test mode.
  1. Skid control sensor
  2. Skid control sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Skid control sensor (open)
  2. Skid control sensor circuit (open)
C1332/37
C1333/38
Open in front speed sensor circuit continues for 0.15 seconds or more.
  1. Skid control sensor (open)
  2. Skid control sensor circuit (open)

HINT:
  1. DTC C0210/33 and C1332/37 relate to the skid control sensor RH.
  2. DTC C0215/34 and C1333/38 relate to the skid control sensor LH.


WIRING DIAGRAM

C117849E04

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in test mode after cleaning or replacement (Click here)


1. READ VALUE OF DATA LIST (SKID CONTROL SENSOR)

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Start the engine and drive the vehicle.

  1. Turn the tester on.

  1. Read the wheel speed value using the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

  1. Select the item "RR (RL) Wheel Speed" in the DATA LIST and read the value displayed on the intelligent tester.

    DATA LIST: ABS/VSC/TRC 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    RR Wheel Speed
    Wheel speed sensor (RR) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Similar to speed indicated on speedometer
    RL Wheel Speed
    Wheel speed sensor (RL) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference in the displayed speed values.

    HINT:
    There is a tolerance of +- 10% in the speedometer indication.



NG
Go to step 4
OK


2. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTCs output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


3. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 8
A

END

4. CHECK SKID CONTROL SENSOR

  1. C118693E01
    Visually check the speed sensor for deformation and damage.

    OK:
    No deformation or damage.
    There is no gap between the sensor and rear axle carrier.



NG
REPLACE SKID CONTROL SENSOR
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR)

  1. C129346E01
    Confirm that the skid control ECU connector and speed sensor connector are properly connected.

  1. Disconnect the skid control ECU connector and the skid control sensor connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance.

    Standard Resistance (LH):
    Tester Connection
    Specified Condition
    A39-16 (RL+) - a1-2 (RL+)
    Below 1 Ω
    A39-15(RL-) - a1-1 (RL-)
    Below 1 Ω

    Standard Resistance (RH):
    Tester Connection
    Specified Condition
    A39-24 (RR+) - Z1-2 (RR+)
    Below 1 Ω
    A39-25 (RR-) - Z1-1 (RR-)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


6. CHECK SKID CONTROL SENSOR (INPUT VOLTAGE)

  1. C129354E01
    Disconnect the speed sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard Voltage (LH):
    Tester Connection
    Specified Condition
    a1-2 (RL+) - Body ground
    5.7 to 17.3 V

    Standard Voltage (RH):
    Tester Connection
    Specified Condition
    Z1-2 (RR+) - Body ground
    5.7 to 17.3 V



NG
REPLACE BRAKE ACTUATOR
OK


7. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


8. REPLACE SKID CONTROL SENSOR
  1. Replace the skid control sensor.


NEXT


9. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR


← C0200/31 Right Front Wheel Speed Sensor Signal (+ 7 more codes) (from Nov 2005)C0226/21 SFR Solenoid Circuit (+ C0236/22, C0246/23, C0256/24) (from Nov 2005) →